Husqvarna GTH2754 owner manual Cleaning

Page 19

MAINTENANCE

After oil has drained completely, close the drain valve turning clockwise. Use the 7/16" (11mm) wrench to apply a small amount of torque to keep it closed. Do not over tighten.

Remove the drain tube and store in a safe place.

Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this man- ual.

Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the tube when taking reading. Keep oil at “FULL” line on dipstick. Tighten cap onto the tube securely when finished.

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled.

NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating.

AIR FILTER

Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See Engine Manual.

ENGINE OIL FILTER

Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. See engine manual.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 17)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

With engine cool, remove filter and plug fuel line sec- tions.

Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

Be sure there are no fuel line leaks and clamps are properly positioned.

Immediately wipe up any spilled gasoline.

CLAMP

CLAMP

FUEL FILTER

FIG. 17

CLEANING

Clean engine, battery, seat, finish, etc. of all foreign matter.

Keep finished surfaces and wheels free of all gasoline, oil, etc.

Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

19

Image 19
Contents GTH2754 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See a and 4B To Attach Nose Roller See Fig Install Mower and Drive Belt SeeCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Routing Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig Mower Drive Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Attachment Clutch See FigTo Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model NO. GTH2754 96023000400 Product no 23 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts 153 Ground DriveRepair Parts Steering Assembly Repair Parts Engine Engine Kohler, Model No. CV740Order parts from 532 18 Seat Seat AssemblyWheels & Tires DecalsLift Assembly Repair Parts Mower Deck 532 19 Deck Weldment Mower 532 12 Retainer Spring Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 19 38-73 Rev 06.10.05 TR/RD/TR

GTH2754 specifications

The Husqvarna GTH2754 is a powerful and versatile garden tractor designed for homeowners looking to maintain their lawns with efficiency and ease. This exceptional machine combines robust construction with innovative technologies, making it a favorite among gardening enthusiasts.

One of the standout features of the GTH2754 is its powerful 27-horsepower Briggs & Stratton engine. This reliable engine ensures that the tractor delivers consistent performance, enabling users to tackle various tasks with confidence. Whether mowing large lawns or navigating tight spaces, the ample power makes it suitable for a range of applications, including mulching and bagging.

The GTH2754 is equipped with a 54-inch cutting deck, allowing for wider cutting swath and a quicker mowing experience. The cutting deck features three large blades designed to give an even and clean cut, ensuring an aesthetically pleasing lawn. With adjustable cutting heights ranging from 1.5 inches to 4 inches, users can customize the lawn's appearance according to their preferences and seasonal requirements.

Comfort is a crucial aspect of the GTH2754, featuring an ergonomic, high-back seat designed for operator comfort during extended use. The seat is adjustable, accommodating different user heights for optimal driving posture. Additionally, the tractor comes equipped with a user-friendly control panel, where operators can easily access key functions like speed control and cutting height adjustment.

The GTH2754 showcases Husqvarna's commitment to innovative technology. The automatic transmission system provides smooth and effortless operation, allowing users to focus on their mowing tasks without needing to grapple with gear shifting. This feature ensures that the tractor can maintain a steady pace, adapting to various terrain conditions effortlessly.

Moreover, the tractor is designed for easy maintenance, with features like an accessible oil filter and removable engine cover. This makes routine checks and servicing straightforward, prolonging the lifespan of the machine.

Overall, the Husqvarna GTH2754 is a robust and user-friendly garden tractor that caters to the needs of modern homeowners. Its powerful engine, large cutting deck, and thoughtful design make yard maintenance not just manageable but also enjoyable. With its combination of performance and comfort, the GTH2754 is indeed a valuable investment for any gardening enthusiast.