Husqvarna GTH2754 owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

00598

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 19

SUSPENSION ARM

01553

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns.The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

BLADE

02548

“B”“B”

FIG. 21

BOTH FRONT PLATE LINKS MUST BE EQUAL IN LENGTH

 

02516

 

NUT “D”

 

NUT “C”

 

02517

TRUNNION

FRONT PLATE

 

 

 

ASSEMBLY

 

 

FIG. 22

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents GTH2754 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See a and 4B To Attach Nose Roller See Fig Install Mower and Drive Belt SeeCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Using the Reverse Operation System To Adjust Gauge Wheels See FigTo Operate Mower See Fig Reverse Operation System ROSTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Belt RoutingTo Check and Adjust Brake To Adjust Attachment Clutch See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model NO. GTH2754 96023000400 Product no 23 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts 153 Ground DriveRepair Parts Steering Assembly Repair Parts Engine Engine Kohler, Model No. CV740Order parts from 532 18 Seat Seat AssemblyWheels & Tires DecalsLift Assembly Repair Parts Mower Deck 532 19 Deck Weldment Mower 532 12 Retainer Spring Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 19 38-73 Rev 06.10.05 TR/RD/TR

GTH2754 specifications

The Husqvarna GTH2754 is a powerful and versatile garden tractor designed for homeowners looking to maintain their lawns with efficiency and ease. This exceptional machine combines robust construction with innovative technologies, making it a favorite among gardening enthusiasts.

One of the standout features of the GTH2754 is its powerful 27-horsepower Briggs & Stratton engine. This reliable engine ensures that the tractor delivers consistent performance, enabling users to tackle various tasks with confidence. Whether mowing large lawns or navigating tight spaces, the ample power makes it suitable for a range of applications, including mulching and bagging.

The GTH2754 is equipped with a 54-inch cutting deck, allowing for wider cutting swath and a quicker mowing experience. The cutting deck features three large blades designed to give an even and clean cut, ensuring an aesthetically pleasing lawn. With adjustable cutting heights ranging from 1.5 inches to 4 inches, users can customize the lawn's appearance according to their preferences and seasonal requirements.

Comfort is a crucial aspect of the GTH2754, featuring an ergonomic, high-back seat designed for operator comfort during extended use. The seat is adjustable, accommodating different user heights for optimal driving posture. Additionally, the tractor comes equipped with a user-friendly control panel, where operators can easily access key functions like speed control and cutting height adjustment.

The GTH2754 showcases Husqvarna's commitment to innovative technology. The automatic transmission system provides smooth and effortless operation, allowing users to focus on their mowing tasks without needing to grapple with gear shifting. This feature ensures that the tractor can maintain a steady pace, adapting to various terrain conditions effortlessly.

Moreover, the tractor is designed for easy maintenance, with features like an accessible oil filter and removable engine cover. This makes routine checks and servicing straightforward, prolonging the lifespan of the machine.

Overall, the Husqvarna GTH2754 is a robust and user-friendly garden tractor that caters to the needs of modern homeowners. Its powerful engine, large cutting deck, and thoughtful design make yard maintenance not just manageable but also enjoyable. With its combination of performance and comfort, the GTH2754 is indeed a valuable investment for any gardening enthusiast.
Top Page Image Contents