Husqvarna GTH2754 owner manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 24

SERVICE AND ADJUSTMENTS

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

FRONT WHEEL (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal.

•Repair tire and reassemble.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

REAR WHEEL -

•Block rear axle securely.

•Remove five (5) hub bolts to allow wheel removal.

•Repair tire and reassemble. Replace and tighten hub bolts securely.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE

COVER

 

q

s

3

 

0066

 

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

02614

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 28

REPLACING BATTERY (See Fig. 29)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents GTH2754 Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See a and 4B Install Mower and Drive Belt See To Attach Nose Roller See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsMower Drive Belt Installation To Replace Mower Drive Belt See FigMower Drive Belt Removal Belt RoutingTo Adjust Attachment Clutch See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model NO. GTH2754 96023000400 Product no 23Electrical KEY Part Description Chassis and Enclosures Repair Parts Ground Drive 153Repair Parts Steering Assembly Repair Parts Engine Engine Kohler, Model No. CV740Order parts from Seat Assembly 532 18 SeatDecals Wheels & TiresLift Assembly Repair Parts Mower Deck 532 19 Deck Weldment Mower 532 12 Retainer Spring Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 19 38-73 Rev 06.10.05 TR/RD/TR

GTH2754 specifications

The Husqvarna GTH2754 is a powerful and versatile garden tractor designed for homeowners looking to maintain their lawns with efficiency and ease. This exceptional machine combines robust construction with innovative technologies, making it a favorite among gardening enthusiasts.

One of the standout features of the GTH2754 is its powerful 27-horsepower Briggs & Stratton engine. This reliable engine ensures that the tractor delivers consistent performance, enabling users to tackle various tasks with confidence. Whether mowing large lawns or navigating tight spaces, the ample power makes it suitable for a range of applications, including mulching and bagging.

The GTH2754 is equipped with a 54-inch cutting deck, allowing for wider cutting swath and a quicker mowing experience. The cutting deck features three large blades designed to give an even and clean cut, ensuring an aesthetically pleasing lawn. With adjustable cutting heights ranging from 1.5 inches to 4 inches, users can customize the lawn's appearance according to their preferences and seasonal requirements.

Comfort is a crucial aspect of the GTH2754, featuring an ergonomic, high-back seat designed for operator comfort during extended use. The seat is adjustable, accommodating different user heights for optimal driving posture. Additionally, the tractor comes equipped with a user-friendly control panel, where operators can easily access key functions like speed control and cutting height adjustment.

The GTH2754 showcases Husqvarna's commitment to innovative technology. The automatic transmission system provides smooth and effortless operation, allowing users to focus on their mowing tasks without needing to grapple with gear shifting. This feature ensures that the tractor can maintain a steady pace, adapting to various terrain conditions effortlessly.

Moreover, the tractor is designed for easy maintenance, with features like an accessible oil filter and removable engine cover. This makes routine checks and servicing straightforward, prolonging the lifespan of the machine.

Overall, the Husqvarna GTH2754 is a robust and user-friendly garden tractor that caters to the needs of modern homeowners. Its powerful engine, large cutting deck, and thoughtful design make yard maintenance not just manageable but also enjoyable. With its combination of performance and comfort, the GTH2754 is indeed a valuable investment for any gardening enthusiast.
Top Page Image Contents