Husqvarna GTH2754 owner manual Assemble Gauge Wheels to Mower Deck See a and 4B

Page 7

ASSEMBLY

•Remove the two (2) bolts and flat washers securing the seat to cardboard packing. Keep the two (2) bolts only and place them with the two (2) identical bolts and four (4) washers in the parts bag. Discard the flat washers and cardboard packing.

•Release L.H. seat slide on seat pan by pulling out on adjustment handle and sliding it to the rear position exposing seat mounting holes from bottom. Slide R.H. slide to same rear position.

•Mount rear of seat on slides using mounting bolts and lock washers as shown.

•Pull out on adjustment handle and slide seat all the way forward. Install front mounting bolts and lock washers. Tighten all mounting bolts securely.

•Lower seat into operating position and sit on seat.Press clutch/brake pedal all the way down. If operating posi- tion is not comfortable, adjust seat.

•To adjust seat: Grasp adjustment handle and pull out, slide seat to desired position and release adjustment handle.

L.H. SEAT

 

SLIDE

SEAT

 

ADJUSTMENT

HANDLE SEAT

PAN

LOCK

WASHERS

02521

R.H. SEAT SLIDE

MOUNTING BOLTS

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

• Be sure all the above assembly steps have been com- pleted.

• Check engine oil level and fill fuel tank with gasoline.

• Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

7

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4A and 4B)

The gauge wheels are designed to keep the mower deck in proper position when operating mower.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•For ease of mower to tractor assembly, set all the gauge wheels in the fourth hole from top. Retain with clevis pins and spring retainers.

RETAINER SPRING

PIN

SHOULDER

BOLT

ADJUSTING

BAR

GAUGE

WHEEL

3/8 WASHER

3/8-16 CENTER

LOCKNUT

 

FIG. 4A

SET ALL WHEELS

TO 4TH HOLE

FROM TOP

FIG. 4B

Page 6 Page 8
Image 7
Page 6 Page 8
Contents GTH2754 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See a and 4B To Attach Nose Roller See Fig Install Mower and Drive Belt SeeCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Routing Mower Drive Belt InstallationTo Replace Mower Drive Belt See Fig Mower Drive Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Attachment Clutch See FigTo Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model NO. GTH2754 96023000400 Product no 23 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts 153 Ground DriveRepair Parts Steering Assembly Repair Parts Engine Engine Kohler, Model No. CV740Order parts from 532 18 Seat Seat AssemblyWheels & Tires DecalsLift Assembly Repair Parts Mower Deck 532 19 Deck Weldment Mower 532 12 Retainer Spring Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 19 38-73 Rev 06.10.05 TR/RD/TR

GTH2754 specifications

The Husqvarna GTH2754 is a powerful and versatile garden tractor designed for homeowners looking to maintain their lawns with efficiency and ease. This exceptional machine combines robust construction with innovative technologies, making it a favorite among gardening enthusiasts.

One of the standout features of the GTH2754 is its powerful 27-horsepower Briggs & Stratton engine. This reliable engine ensures that the tractor delivers consistent performance, enabling users to tackle various tasks with confidence. Whether mowing large lawns or navigating tight spaces, the ample power makes it suitable for a range of applications, including mulching and bagging.

The GTH2754 is equipped with a 54-inch cutting deck, allowing for wider cutting swath and a quicker mowing experience. The cutting deck features three large blades designed to give an even and clean cut, ensuring an aesthetically pleasing lawn. With adjustable cutting heights ranging from 1.5 inches to 4 inches, users can customize the lawn's appearance according to their preferences and seasonal requirements.

Comfort is a crucial aspect of the GTH2754, featuring an ergonomic, high-back seat designed for operator comfort during extended use. The seat is adjustable, accommodating different user heights for optimal driving posture. Additionally, the tractor comes equipped with a user-friendly control panel, where operators can easily access key functions like speed control and cutting height adjustment.

The GTH2754 showcases Husqvarna's commitment to innovative technology. The automatic transmission system provides smooth and effortless operation, allowing users to focus on their mowing tasks without needing to grapple with gear shifting. This feature ensures that the tractor can maintain a steady pace, adapting to various terrain conditions effortlessly.

Moreover, the tractor is designed for easy maintenance, with features like an accessible oil filter and removable engine cover. This makes routine checks and servicing straightforward, prolonging the lifespan of the machine.

Overall, the Husqvarna GTH2754 is a robust and user-friendly garden tractor that caters to the needs of modern homeowners. Its powerful engine, large cutting deck, and thoughtful design make yard maintenance not just manageable but also enjoyable. With its combination of performance and comfort, the GTH2754 is indeed a valuable investment for any gardening enthusiast.
Top Page Image Contents