Husqvarna GTH2548XP To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 14

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

ATTACHMENT CLUTCH

LIFT LEVER

SWITCH PULL OUT TO

HIGEST PO-

“ENGAGE”

SITION

 

LOWEST

 

POSITION

PUSH IN TO

 

“DISENGAGE”

DEFLECTOR

 

 

SHIELD

FIG. 10

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

IMPORTANT: THE MOTION CONTROL LEVER RETURNS TO NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS FULLY DEPRESSED.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

FIG. 11

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents GTH2548XP General Operation IV. ServiceSafe Operation Practices for RIDE-ON Mowers II. Slope OperationSafety Rules Table of Contents Unassembled Parts HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Operation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionBefore Each USE MaintenanceGeneral Recommendations Tractor Engine Engine OIL Filter CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Attachment Clutch See FigTo Check and Adjust Brake To Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT Front Wheel TOE-IN/CAMBERTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor - Model NO. GTH2548XPGTH2548XPB, Product no 56Electrical KEY Part Description Chassis and Enclosures 532 17 54-76 Bracket, Chassis Front Ground Drive 153532 14 Bracket Shift Steering Assembly 36 532 18 67-99 Tie Rod Engine Spark Arrester KIT KEY Part DescriptionSeat Assembly Wheels & Tires DecalsLift Assembly Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 18 47-61 Rev 05.23.03 RD/TR

GTH2548XP specifications

The Husqvarna GTH2548XP is a highly versatile and powerful riding mower designed for homeowners who value efficiency, durability, and ease of use. With its robust features and advanced technologies, this lawn tractor stands out as an excellent choice for maintaining expansive lawns and gardens.

One of the key features of the GTH2548XP is its 24 HP Briggs & Stratton engine, which provides ample power for tackling tough terrain and long grass. The hydrostatic transmission offers seamless speed control, allowing the operator to navigate complex landscapes with precision and ease. This technology ensures that users can adjust their speed without the need for cumbersome gear shifting, resulting in a smoother mowing experience.

The 48-inch cutting deck is another highlight of the GTH2548XP. This wide deck allows for efficient mowing and covers more ground in less time. Equipped with a reinforced cutting system and three high-performance blades, it delivers a clean, even cut across various grass types. Additionally, the deck features an air-induction mowing technology that enhances airflow within the deck, ensuring a superior cut quality and reducing clumping.

Comfort is paramount in the design of the GTH2548XP. The adjustable high back seat provides ample lumbar support, allowing for extended periods of use without discomfort. The ergonomic steering wheel and intuitive control layout make it easy for operators of all skill levels to handle the machine with confidence. Furthermore, the large, easy-to-read instrument panel keeps essential information within reach, making it simple to monitor the mower’s performance.

Safety features are also prominent in the GTH2548XP. The mower is equipped with a safety switch under the seat, cutting off power if the operator leaves the seat, thus preventing accidents. Additionally, the durable construction of the mower ensures longevity and reliability, even under demanding conditions.

In conclusion, the Husqvarna GTH2548XP combines power, comfort, and safety into an exceptional lawn care machine. Whether you're maintaining a large estate or a smaller yard, this riding mower, with its array of advanced features and technologies, can help you achieve a well-manicured lawn with ease and efficiency. Ideal for homeowners seeking long-term performance, the GTH2548XP is a sound investment for anyone serious about lawn maintenance.
Top Page Image Contents