Husqvarna GTH2548XP owner manual Off

Page 30

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

 

CORRECTION

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves seat

 

 

 

corrected, contact an authorized service center/

with attachment clutch

 

 

 

department.

engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents GTH2548XP General Operation IV. ServiceSafe Operation Practices for RIDE-ON Mowers II. Slope OperationSafety Rules Table of Contents Unassembled Parts HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionMaintenance General RecommendationsBefore Each USE Tractor Engine Engine OIL Filter CleaningAIR Filter MufflerService and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Adjust Attachment Clutch See Fig To Check and Adjust BrakeTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT Front Wheel TOE-IN/CAMBERTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor - Model NO. GTH2548XPGTH2548XPB, Product no 56Electrical KEY Part Description Chassis and Enclosures 532 17 54-76 Bracket, Chassis Front Ground Drive 153532 14 Bracket Shift Steering Assembly 36 532 18 67-99 Tie Rod Engine Spark Arrester KIT KEY Part DescriptionSeat Assembly Wheels & Tires DecalsLift Assembly Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 18 47-61 Rev 05.23.03 RD/TR

GTH2548XP specifications

The Husqvarna GTH2548XP is a highly versatile and powerful riding mower designed for homeowners who value efficiency, durability, and ease of use. With its robust features and advanced technologies, this lawn tractor stands out as an excellent choice for maintaining expansive lawns and gardens.

One of the key features of the GTH2548XP is its 24 HP Briggs & Stratton engine, which provides ample power for tackling tough terrain and long grass. The hydrostatic transmission offers seamless speed control, allowing the operator to navigate complex landscapes with precision and ease. This technology ensures that users can adjust their speed without the need for cumbersome gear shifting, resulting in a smoother mowing experience.

The 48-inch cutting deck is another highlight of the GTH2548XP. This wide deck allows for efficient mowing and covers more ground in less time. Equipped with a reinforced cutting system and three high-performance blades, it delivers a clean, even cut across various grass types. Additionally, the deck features an air-induction mowing technology that enhances airflow within the deck, ensuring a superior cut quality and reducing clumping.

Comfort is paramount in the design of the GTH2548XP. The adjustable high back seat provides ample lumbar support, allowing for extended periods of use without discomfort. The ergonomic steering wheel and intuitive control layout make it easy for operators of all skill levels to handle the machine with confidence. Furthermore, the large, easy-to-read instrument panel keeps essential information within reach, making it simple to monitor the mower’s performance.

Safety features are also prominent in the GTH2548XP. The mower is equipped with a safety switch under the seat, cutting off power if the operator leaves the seat, thus preventing accidents. Additionally, the durable construction of the mower ensures longevity and reliability, even under demanding conditions.

In conclusion, the Husqvarna GTH2548XP combines power, comfort, and safety into an exceptional lawn care machine. Whether you're maintaining a large estate or a smaller yard, this riding mower, with its array of advanced features and technologies, can help you achieve a well-manicured lawn with ease and efficiency. Ideal for homeowners seeking long-term performance, the GTH2548XP is a sound investment for anyone serious about lawn maintenance.
Top Page Image Contents