Husqvarna GTH2548XP owner manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 22

SERVICE AND ADJUSTMENTS

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM

OF MOWER

 

EDGE OF

TO GROUND

 

MOWER

 

 

TO GROUND

A

GROUND LINE

A

 

 

FIG. 19

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns.The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

BLADE

“B”“B”

FIG. 21

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents GTH2548XP General Operation IV. ServiceSafe Operation Practices for RIDE-ON Mowers II. Slope OperationSafety Rules Table of Contents Unassembled Parts HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceBefore Each USE Tractor Engine Engine OIL Filter CleaningAIR Filter MufflerTo Install Mower Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Check and Adjust Brake To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT Front Wheel TOE-IN/CAMBERTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove CABLES, Reverse OrderTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor - Model NO. GTH2548XPGTH2548XPB, Product no 56Electrical KEY Part Description Chassis and Enclosures 532 17 54-76 Bracket, Chassis Front Ground Drive 153532 14 Bracket Shift Steering Assembly 36 532 18 67-99 Tie Rod Engine Spark Arrester KIT KEY Part DescriptionSeat Assembly Wheels & Tires DecalsLift Assembly Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 18 47-61 Rev 05.23.03 RD/TR

GTH2548XP specifications

The Husqvarna GTH2548XP is a highly versatile and powerful riding mower designed for homeowners who value efficiency, durability, and ease of use. With its robust features and advanced technologies, this lawn tractor stands out as an excellent choice for maintaining expansive lawns and gardens.

One of the key features of the GTH2548XP is its 24 HP Briggs & Stratton engine, which provides ample power for tackling tough terrain and long grass. The hydrostatic transmission offers seamless speed control, allowing the operator to navigate complex landscapes with precision and ease. This technology ensures that users can adjust their speed without the need for cumbersome gear shifting, resulting in a smoother mowing experience.

The 48-inch cutting deck is another highlight of the GTH2548XP. This wide deck allows for efficient mowing and covers more ground in less time. Equipped with a reinforced cutting system and three high-performance blades, it delivers a clean, even cut across various grass types. Additionally, the deck features an air-induction mowing technology that enhances airflow within the deck, ensuring a superior cut quality and reducing clumping.

Comfort is paramount in the design of the GTH2548XP. The adjustable high back seat provides ample lumbar support, allowing for extended periods of use without discomfort. The ergonomic steering wheel and intuitive control layout make it easy for operators of all skill levels to handle the machine with confidence. Furthermore, the large, easy-to-read instrument panel keeps essential information within reach, making it simple to monitor the mower’s performance.

Safety features are also prominent in the GTH2548XP. The mower is equipped with a safety switch under the seat, cutting off power if the operator leaves the seat, thus preventing accidents. Additionally, the durable construction of the mower ensures longevity and reliability, even under demanding conditions.

In conclusion, the Husqvarna GTH2548XP combines power, comfort, and safety into an exceptional lawn care machine. Whether you're maintaining a large estate or a smaller yard, this riding mower, with its array of advanced features and technologies, can help you achieve a well-manicured lawn with ease and efficiency. Ideal for homeowners seeking long-term performance, the GTH2548XP is a sound investment for anyone serious about lawn maintenance.
Top Page Image Contents