Husqvarna GTH2548XP owner manual Mowing Tips, Purge Transmission

Page 16

OPERATION

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the en- gine is running, move throttle control to slow position. Disengage parking brake

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. Disengage parking brake.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the mo- tion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Tire chains cannot be used when the mower housing is attached to tractor.

•Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 12).

00272

FIG. 12

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents GTH2548XP IV. Service Safe Operation Practices for RIDE-ON MowersGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Operation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceBefore Each USE Tractor Engine Cleaning AIR FilterEngine OIL Filter MufflerTo Install Mower Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Check and Adjust Brake To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Attach Jumper Cables To Remove CABLES, Reverse OrderTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor - Model NO. GTH2548XPGTH2548XPB, Product no 56Electrical KEY Part Description Chassis and Enclosures 532 17 54-76 Bracket, Chassis Front Ground Drive 153532 14 Bracket Shift Steering Assembly 36 532 18 67-99 Tie Rod Engine Spark Arrester KIT KEY Part DescriptionSeat Assembly Wheels & Tires DecalsLift Assembly Mower Deck Repair Parts Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 18 47-61 Rev 05.23.03 RD/TR

GTH2548XP specifications

The Husqvarna GTH2548XP is a highly versatile and powerful riding mower designed for homeowners who value efficiency, durability, and ease of use. With its robust features and advanced technologies, this lawn tractor stands out as an excellent choice for maintaining expansive lawns and gardens.

One of the key features of the GTH2548XP is its 24 HP Briggs & Stratton engine, which provides ample power for tackling tough terrain and long grass. The hydrostatic transmission offers seamless speed control, allowing the operator to navigate complex landscapes with precision and ease. This technology ensures that users can adjust their speed without the need for cumbersome gear shifting, resulting in a smoother mowing experience.

The 48-inch cutting deck is another highlight of the GTH2548XP. This wide deck allows for efficient mowing and covers more ground in less time. Equipped with a reinforced cutting system and three high-performance blades, it delivers a clean, even cut across various grass types. Additionally, the deck features an air-induction mowing technology that enhances airflow within the deck, ensuring a superior cut quality and reducing clumping.

Comfort is paramount in the design of the GTH2548XP. The adjustable high back seat provides ample lumbar support, allowing for extended periods of use without discomfort. The ergonomic steering wheel and intuitive control layout make it easy for operators of all skill levels to handle the machine with confidence. Furthermore, the large, easy-to-read instrument panel keeps essential information within reach, making it simple to monitor the mower’s performance.

Safety features are also prominent in the GTH2548XP. The mower is equipped with a safety switch under the seat, cutting off power if the operator leaves the seat, thus preventing accidents. Additionally, the durable construction of the mower ensures longevity and reliability, even under demanding conditions.

In conclusion, the Husqvarna GTH2548XP combines power, comfort, and safety into an exceptional lawn care machine. Whether you're maintaining a large estate or a smaller yard, this riding mower, with its array of advanced features and technologies, can help you achieve a well-manicured lawn with ease and efficiency. Ideal for homeowners seeking long-term performance, the GTH2548XP is a sound investment for anyone serious about lawn maintenance.
Top Page Image Contents