Husqvarna GTH27V52LS To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

K

J

L

Fig. 7

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents GTH27V52LS General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Using the Reverse Operation SystemTo Stop Mower Blades To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig Install ANTI-SWAY BAR S if Equipped Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigSecure with small washer and small retainer spring as shown To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel See FigReplacing Battery See Fig To Start Engine with a Weak Battery see FIGTo Remove CABLES, Reverse Order Transmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Service Notes Service Notes Service Notes Ggus 01.07.09 AP

GTH27V52LS specifications

The Husqvarna GTH27V52LS is a robust and versatile riding lawn tractor designed to provide an optimal mowing experience for homeowners with larger landscapes. Known for its powerful performance and advanced features, this model stands out as a reliable choice for tackling various lawn care tasks.

At the heart of the GTH27V52LS is its 27-horsepower Kohler engine, delivering ample power to handle expansive lawns with ease. The efficient engine provides a balance between performance and fuel economy, ensuring you can work for longer periods without frequent refueling. Additionally, the hydrostatic transmission allows for smooth, infinite speed control, making it simple to maneuver around obstacles and navigate uneven terrain.

One of the standout features of the GTH27V52LS is its 52-inch cutting deck, which provides an impressive cutting width for efficient mowing of large areas. The deck is designed with oversized tires that enhance traction and stability, ensuring a clean cut even on the toughest terrains. Furthermore, the deck height can easily be adjusted to suit varying grass lengths, enabling precise cutting for a polished finish.

The GTH27V52LS incorporates innovative mowing technologies, such as the Air Induction Mowing Technology, which improves airflow within the deck for a superior grass cutting and grass collection performance. This results in a healthier lawn with minimal clumping and enhanced mulching capabilities.

Comfort is also a priority in the design of the GTH27V52LS. The spacious, ergonomic seat offers ample cushioning and adjustable settings, ensuring a comfortable ride during extended mowing sessions. The easy-to-use controls are strategically located for convenience, enabling operators to maintain focus on the task at hand without interruptions.

Additional features include an integrated roll-over protection system for added safety, as well as a range of accessories, such as baggers and tow-behind attachments, that enhance the tractor’s functionality throughout the year. The durable construction and high-quality materials ensure that the Husqvarna GTH27V52LS is built to withstand the rigors of regular use, making it a long-lasting investment for any homeowner.

In summary, the Husqvarna GTH27V52LS combines power, technology, and user-friendly design, making it an outstanding choice for anyone in need of a reliable riding lawn tractor. Its exceptional performance and innovative features provide an efficient solution for maintaining large lawns, ensuring your outdoor space remains pristine year-round.
Top Page Image Contents