Husqvarna YTH2754XP To USE Cruise Control -J See Fig, To Adjust Mower Cutting Height See Fig

Page 13

OPERATION

J

K

L

FIG. 17

TO USE CRUISE CONTROL -J (See Fig. 17)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 18)

The position of the attachment lift lever (A) determines the cutting height.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 19)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

A

FIG. 18

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

FIG.19

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents YTH2754XP Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts BatteryMower Mower Front Wheel Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Unpack CartonFirst Install ANTI-SWAY BAR S Install Mower and Drive Belt7/16 Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To USE Cruise Control -J See FigUsing the Reverse Operation System Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceBefore Each USE Tractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsTo Install Mower Service and AdjustmentsTractor See Fig To Remove MowerTurn nut right Turn nut left To raise mower To Check Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor Model NO. YTH2754XP 96041000501, Product no 41 SchematicElectrical KEY Part NO. NO. Description Chassis Tractor Model NO. YTH2754XP 96041000501, Product no 41 Drive KEY Part Description Steering Assembly Engine Spark Arrester KITSeat Assembly Wheels and Tires DecalsMower Deck KEY Part NO. NO. Description Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement

YTH2754XP specifications

The Husqvarna YTH2754XP is a versatile and efficient riding mower designed for homeowners seeking a robust solution for maintaining their lawns. With its powerful features and user-friendly design, it stands out as an excellent choice for those looking to achieve a beautifully manicured lawn with minimal effort.

One of the standout features of the YTH2754XP is its 27-horsepower engine. Powered by a reliable Briggs & Stratton® motor, it provides ample power for tackling various lawn conditions, making it easy to cut through thick grass and navigate uneven terrains. The 54-inch cutting deck ensures a wide cutting path, enabling users to cover more ground in less time while delivering a clean, precise cut.

The cutting deck is constructed with high-quality materials, featuring a reinforced design that can withstand the rigors of frequent use. With three anti-scalp wheels, the deck maintains consistent height for an even cut, reducing the risk of grass scalping on uneven surfaces. Additionally, the deck's cutting height can be easily adjusted, allowing users to choose the perfect height for their specific grass type and growing conditions.

Husqvarna has incorporated several advanced technologies in the YTH2754XP to enhance the mowing experience. The automatic transmission allows for smooth acceleration and deceleration, making it easier to navigate tight spots and corners. The ergonomic steering wheel and comfortable seat ensure a pleasant ride, minimizing fatigue during longer mowing sessions.

The YTH2754XP also features a pedal-operated hydrostatic transmission, which offers seamless speed and direction changes without the need for manual clutching or shifting. This system allows for precise control and maneuverability, particularly in challenging landscaping areas.

In terms of maintenance, the YTH2754XP has been designed with user convenience in mind. The integrated deck wash system makes cleaning the underside of the cutting deck simple, preventing grass build-up that can affect cutting performance. Furthermore, the easy-access battery compartment and oil filter simplify routine maintenance tasks.

With its combination of power, durability, and innovative features, the Husqvarna YTH2754XP is a reliable choice for homeowners looking to invest in a quality riding mower that makes lawn care a breeze. Its blend of cutting-edge technology and user-friendly design ensures that even the most challenging mowing tasks can be accomplished with ease and efficiency.
Top Page Image Contents