Husqvarna YTH2754XP Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping pur- poses.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

(1)

Utility knife

(1)

9/16" wrench

(1)

Pliers

(2)

7/16" wrenches

(1)

Tire Pressure Gauge

When right or left hand is mentioned in this manual, it means from your point of view, when you are in the operat- ing position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Remove mower and packing materials.

•Check for any additional loose parts or cartons and remove.

CONNECT BATTERY (See Figs. 1)

CAUTION: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift hood to raised position.

•Remove terminal protective caps and discard.

•If this battery is put into service after month and year indicated on label (L) (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in the Maintenance section of this manual for charging instructions).

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

L

02954

FIG. 1

ADJUST SEAT (See Fig. 2)

•Sit in seat.

•Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down.

•Release lever to lock seat in position.

A

FIG. 2

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Raise attachment lift lever to its highest position.

•Release parking brake by depressing brake pedal.

•Place freewheel control in disengaged position to dis- engage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START" in the Operation section of this manual). After engine has started, move throttle control to idle (slow) position.

•Release parking brake.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents YTH2754XP General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Mower Mower Front Wheel BatteryUnassembled Parts Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Unpack CartonInstall Mower and Drive Belt First Install ANTI-SWAY BAR S7/16 Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control -J See FigReverse Operation System ROS Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Maintenance Lubrication ChartBefore Each USE Brake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTractor See Fig Service and AdjustmentsTo Install Mower To Remove MowerTurn nut right Turn nut left To raise mower To Replace Mower Blade Drive Belt To Check BrakeTo Replace Motion Drive Belt To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor Model NO. YTH2754XP 96041000501, Product no 41Electrical KEY Part NO. NO. Description Chassis Tractor Model NO. YTH2754XP 96041000501, Product no 41 Drive KEY Part Description Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck KEY Part NO. NO. Description Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement

YTH2754XP specifications

The Husqvarna YTH2754XP is a versatile and efficient riding mower designed for homeowners seeking a robust solution for maintaining their lawns. With its powerful features and user-friendly design, it stands out as an excellent choice for those looking to achieve a beautifully manicured lawn with minimal effort.

One of the standout features of the YTH2754XP is its 27-horsepower engine. Powered by a reliable Briggs & Stratton® motor, it provides ample power for tackling various lawn conditions, making it easy to cut through thick grass and navigate uneven terrains. The 54-inch cutting deck ensures a wide cutting path, enabling users to cover more ground in less time while delivering a clean, precise cut.

The cutting deck is constructed with high-quality materials, featuring a reinforced design that can withstand the rigors of frequent use. With three anti-scalp wheels, the deck maintains consistent height for an even cut, reducing the risk of grass scalping on uneven surfaces. Additionally, the deck's cutting height can be easily adjusted, allowing users to choose the perfect height for their specific grass type and growing conditions.

Husqvarna has incorporated several advanced technologies in the YTH2754XP to enhance the mowing experience. The automatic transmission allows for smooth acceleration and deceleration, making it easier to navigate tight spots and corners. The ergonomic steering wheel and comfortable seat ensure a pleasant ride, minimizing fatigue during longer mowing sessions.

The YTH2754XP also features a pedal-operated hydrostatic transmission, which offers seamless speed and direction changes without the need for manual clutching or shifting. This system allows for precise control and maneuverability, particularly in challenging landscaping areas.

In terms of maintenance, the YTH2754XP has been designed with user convenience in mind. The integrated deck wash system makes cleaning the underside of the cutting deck simple, preventing grass build-up that can affect cutting performance. Furthermore, the easy-access battery compartment and oil filter simplify routine maintenance tasks.

With its combination of power, durability, and innovative features, the Husqvarna YTH2754XP is a reliable choice for homeowners looking to invest in a quality riding mower that makes lawn care a breeze. Its blend of cutting-edge technology and user-friendly design ensures that even the most challenging mowing tasks can be accomplished with ease and efficiency.
Top Page Image Contents