Husqvarna YTH2754XP owner manual To Replace Mower Blade Drive Belt, To Check Brake

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 32)

Park tractor on a level surface. Engage parking brake.

Lower attachment lift lever to its lowest position.

Disengage belt tension rod (K) from lock bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a firm grip on rod and release slowly.

Remove screws (P) from mandrel covers (Q) and re- move covers.

Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

Remove belt from electric clutch pulley (M), both man- drel pulleys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

Install belt around all mandrel pulleys (R) and around idler pulleys (S) as shown.

Install belt onto electric clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

Reassemble mandrel covers (Q). Securely tighten all screws.

Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

Raise attachment lift lever to highest position.

P

Q

LM

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

TO REPLACE MOTION DRIVE BELT

(See Fig. 33)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

• Disconnect clutch wire harness (A).

• Remove anti-rotation link (B) on right side of tractor.

• Remove belt from stationary idler (C) and clutching

idler (D).

• Remove belt from centerspan idler (E).

• Pull belt slack toward rear of tractor. Carefully remove

belt upwards from transmission input pulley and over

cooling fan blades (F).

• Remove belt downward from engine pulley and around

electric clutch (G).

• Slide belt toward rear of tractor, off the steering plate

KR

R

S

P

Q

(H) and remove from tractor.

BELT INSTALLATION -

• Install new belt from tractor rear to front, over the steer-

ing plate (H) and above clutch brake pedal shaft (J).

• Pull belt toward front of tractor and roll belt around

electric clutch and onto engine pulley (G).

• Pull belt toward rear of tractor. Carefully work belt down

around transmission cooling fan and onto the input

pulley (F). Be sure belt is inside the belt keeper.

• Install belt on centerspan idler (E).

R

FIG. 32

• Install belt through stationary idler (C) and clutching

idler (D).

• Reinstall anti-rotation link (B) on right side of tractor.

Tighten securely.

• Reconnect clutch harness (A).

• Make sure belt is in all pulley grooves and inside all

belt guides and keepers.

• Install mower (See “TO INSTALL MOWER” in this sec-

tion of manual).

23

Image 23
Contents YTH2754XP II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Slope Sheet BatteryUnassembled Parts Mower Mower Front WheelUnpack Carton AssemblyTools Required for Assembly To Remove Tractor from CartonFirst Install ANTI-SWAY BAR S Install Mower and Drive Belt7/16 Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Reverse Operation System ROS on Position Know Your TractorStopping HOW to USE Your TractorTo USE Cruise Control -J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System CharacteristicsTo Operate on Hills Service REMINDER/HOUR MeterUsing the Reverse Operation System Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceLubrication Chart Tires BatteryTractor Brake OperationEngine Spark Plugs CleaningEngine OIL Filter MufflerTo Remove Mower Service and AdjustmentsTo Install Mower Tractor See FigTurn nut right Turn nut left To raise mower To Replace Motion Drive Belt To Replace Mower Blade Drive BeltTo Check Brake To Attach Jumper Cables To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Tractor Model NO. YTH2754XP 96041000501, Product no 41 SchematicElectrical KEY Part NO. NO. Description Chassis Tractor Model NO. YTH2754XP 96041000501, Product no 41 Drive KEY Part Description Steering Assembly Engine Spark Arrester KITSeat Assembly Wheels and Tires DecalsMower Deck KEY Part NO. NO. Description Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement

YTH2754XP specifications

The Husqvarna YTH2754XP is a versatile and efficient riding mower designed for homeowners seeking a robust solution for maintaining their lawns. With its powerful features and user-friendly design, it stands out as an excellent choice for those looking to achieve a beautifully manicured lawn with minimal effort.

One of the standout features of the YTH2754XP is its 27-horsepower engine. Powered by a reliable Briggs & StrattonĀ® motor, it provides ample power for tackling various lawn conditions, making it easy to cut through thick grass and navigate uneven terrains. The 54-inch cutting deck ensures a wide cutting path, enabling users to cover more ground in less time while delivering a clean, precise cut.

The cutting deck is constructed with high-quality materials, featuring a reinforced design that can withstand the rigors of frequent use. With three anti-scalp wheels, the deck maintains consistent height for an even cut, reducing the risk of grass scalping on uneven surfaces. Additionally, the deck's cutting height can be easily adjusted, allowing users to choose the perfect height for their specific grass type and growing conditions.

Husqvarna has incorporated several advanced technologies in the YTH2754XP to enhance the mowing experience. The automatic transmission allows for smooth acceleration and deceleration, making it easier to navigate tight spots and corners. The ergonomic steering wheel and comfortable seat ensure a pleasant ride, minimizing fatigue during longer mowing sessions.

The YTH2754XP also features a pedal-operated hydrostatic transmission, which offers seamless speed and direction changes without the need for manual clutching or shifting. This system allows for precise control and maneuverability, particularly in challenging landscaping areas.

In terms of maintenance, the YTH2754XP has been designed with user convenience in mind. The integrated deck wash system makes cleaning the underside of the cutting deck simple, preventing grass build-up that can affect cutting performance. Furthermore, the easy-access battery compartment and oil filter simplify routine maintenance tasks.

With its combination of power, durability, and innovative features, the Husqvarna YTH2754XP is a reliable choice for homeowners looking to invest in a quality riding mower that makes lawn care a breeze. Its blend of cutting-edge technology and user-friendly design ensures that even the most challenging mowing tasks can be accomplished with ease and efficiency.