Husqvarna YTH2454T owner manual Tractor, Brake Operation, Tires, Blade Care, Battery

Page 18

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

 

02828

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be sharp. Replace worn, bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is haz- ardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 23)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

BLADE

MANDREL

 

ASSEMBLY

 

CENTER

 

HOLE

BLADE BOLT

 

(SPECIAL)

02544

 

 

STAR

FIG. 23

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents YTH2454T General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Mower Mower Front WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Unpack CartonInstall Mower and Drive Belt First Install ANTI-SWAY BAR S7/16 Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control -J See FigReverse Operation System ROS Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Maintenance Lubrication ChartBefore Each USE Brake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTractor See Fig Service and AdjustmentsTo Install Mower To Remove MowerTurn nut right Turn nut left To raise mower To Replace Mower Blade Drive Belt To Check BrakeTo Replace Motion Drive Belt To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor Model NO. YTH2454T 96043002203, Product no 43Electrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive KEY Part NO. NO.DESCRIPTION Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck KEY Part NO. NO.DESCRIPTION Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2454T specifications

The Husqvarna YTH2454T is an exceptional riding lawn mower designed to provide both efficient performance and comfort for homeowners with larger lawns. With a powerful engine and a range of innovative features, this machine stands out as a reliable option for residential lawn care.

At the heart of the YTH2454T is a robust 24 horsepower Briggs & Stratton V-Twin engine. This reliable power source ensures smooth operation and ample power for tackling any mowing task. The engine's design allows for increased durability and reduced vibration, making mowing a more enjoyable experience. The hydrostatic transmission provides effortless speed control, allowing the operator to maintain a consistent pace while moving forward or in reverse, without the need for shifting gears.

One of the standout characteristics of the YTH2454T is its 54-inch cutting deck, which enables the mower to cover large areas efficiently. The deck is designed with a stamped, reinforced steel construction, providing durability and longevity. The cutting height can be easily adjusted from 1.5 to 4 inches to suit different grass types and conditions, ensuring a clean and precise cut every time.

Husqvarna has incorporated innovative technologies to enhance the user experience. The air induction mowing technology improves grass lift and guarantees an even cut, while the deck wash port allows for easy cleaning of the mower deck after use. The ergonomic steering wheel and comfortable seat reduce operator fatigue, even during extended mowing sessions.

Additionally, the YTH2454T features an integrated mulching capability, enabling the mower to finely chop grass clippings and return them to the lawn, enriching the soil and promoting healthy growth. The easy-access controls make it user-friendly, ensuring that both novice and experienced users can operate it with ease.

With a tight turning radius of 16 inches, the Husqvarna YTH2454T excels in maneuverability, allowing it to navigate around landscaping, trees, and flower beds with minimal effort. This combination of power, comfort, and advanced features makes the YTH2454T a top choice for homeowners looking for a reliable and efficient riding mower. Whether maintaining a sprawling lawn or tackling rough terrain, the Husqvarna YTH2454T proves to be an excellent investment for achieving a beautifully manicured yard.
Top Page Image Contents