Husqvarna YTH2454T Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping pur- poses.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

(1)

Utility knife

(1)

9/16" wrench

(1)

Pliers

(1)

Tire Pressure Gauge

 

 

When right or left hand is mentioned in this manual, it means from your point of view, when you are in the operat- ing position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Remove mower and packing materials.

•Check for any additional loose parts or cartons and remove.

A

FIG. 2

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

CHECK BATTERY (See Fig. 1)

•Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (L) (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

L

02931

FIG. 1

ADJUST SEAT (See Fig. 2)

•Sit in seat.

•Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down.

•Release lever to lock seat in position.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Raise attachment lift lever to its highest position.

•Release parking brake by depressing brake pedal.

•Place freewheel control in disengaged position to dis- engage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START" in the Operation section of this manual). After engine has started, move throttle control to idle (slow) position.

•Release parking brake.

•Slowly depress forward drive pedal and drive tractor off skid.

•Apply brake to stop tractor and set parking brake.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents YTH2454T General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Mower Mower Front WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Unpack CartonInstall Mower and Drive Belt First Install ANTI-SWAY BAR S7/16 Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control -J See FigReverse Operation System ROS Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Maintenance Lubrication ChartBefore Each USE Brake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTractor See Fig Service and AdjustmentsTo Install Mower To Remove MowerTurn nut right Turn nut left To raise mower To Replace Mower Blade Drive Belt To Check BrakeTo Replace Motion Drive Belt To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor Model NO. YTH2454T 96043002203, Product no 43Electrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive KEY Part NO. NO.DESCRIPTION Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck KEY Part NO. NO.DESCRIPTION Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2454T specifications

The Husqvarna YTH2454T is an exceptional riding lawn mower designed to provide both efficient performance and comfort for homeowners with larger lawns. With a powerful engine and a range of innovative features, this machine stands out as a reliable option for residential lawn care.

At the heart of the YTH2454T is a robust 24 horsepower Briggs & Stratton V-Twin engine. This reliable power source ensures smooth operation and ample power for tackling any mowing task. The engine's design allows for increased durability and reduced vibration, making mowing a more enjoyable experience. The hydrostatic transmission provides effortless speed control, allowing the operator to maintain a consistent pace while moving forward or in reverse, without the need for shifting gears.

One of the standout characteristics of the YTH2454T is its 54-inch cutting deck, which enables the mower to cover large areas efficiently. The deck is designed with a stamped, reinforced steel construction, providing durability and longevity. The cutting height can be easily adjusted from 1.5 to 4 inches to suit different grass types and conditions, ensuring a clean and precise cut every time.

Husqvarna has incorporated innovative technologies to enhance the user experience. The air induction mowing technology improves grass lift and guarantees an even cut, while the deck wash port allows for easy cleaning of the mower deck after use. The ergonomic steering wheel and comfortable seat reduce operator fatigue, even during extended mowing sessions.

Additionally, the YTH2454T features an integrated mulching capability, enabling the mower to finely chop grass clippings and return them to the lawn, enriching the soil and promoting healthy growth. The easy-access controls make it user-friendly, ensuring that both novice and experienced users can operate it with ease.

With a tight turning radius of 16 inches, the Husqvarna YTH2454T excels in maneuverability, allowing it to navigate around landscaping, trees, and flower beds with minimal effort. This combination of power, comfort, and advanced features makes the YTH2454T a top choice for homeowners looking for a reliable and efficient riding mower. Whether maintaining a sprawling lawn or tackling rough terrain, the Husqvarna YTH2454T proves to be an excellent investment for achieving a beautifully manicured yard.
Top Page Image Contents