Husqvarna YTH2454T owner manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 26

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents YTH2454T General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Mower Mower Front WheelTo Remove Tractor from Carton AssemblyTools Required for Assembly Unpack CartonInstall Mower and Drive Belt First Install ANTI-SWAY BAR S7/16 Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control -J See FigReverse Operation System ROS Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Before Each USE MaintenanceLubrication Chart Brake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTractor See Fig Service and AdjustmentsTo Install Mower To Remove MowerTurn nut right Turn nut left To raise mower To Replace Motion Drive Belt To Replace Mower Blade Drive BeltTo Check Brake To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor Model NO. YTH2454T 96043002203, Product no 43Electrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive KEY Part NO. NO.DESCRIPTION Steering Assembly Spark Arrester KIT EngineSeat Assembly Decals Wheels and TiresMower Deck KEY Part NO. NO.DESCRIPTION Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2454T specifications

The Husqvarna YTH2454T is an exceptional riding lawn mower designed to provide both efficient performance and comfort for homeowners with larger lawns. With a powerful engine and a range of innovative features, this machine stands out as a reliable option for residential lawn care.

At the heart of the YTH2454T is a robust 24 horsepower Briggs & Stratton V-Twin engine. This reliable power source ensures smooth operation and ample power for tackling any mowing task. The engine's design allows for increased durability and reduced vibration, making mowing a more enjoyable experience. The hydrostatic transmission provides effortless speed control, allowing the operator to maintain a consistent pace while moving forward or in reverse, without the need for shifting gears.

One of the standout characteristics of the YTH2454T is its 54-inch cutting deck, which enables the mower to cover large areas efficiently. The deck is designed with a stamped, reinforced steel construction, providing durability and longevity. The cutting height can be easily adjusted from 1.5 to 4 inches to suit different grass types and conditions, ensuring a clean and precise cut every time.

Husqvarna has incorporated innovative technologies to enhance the user experience. The air induction mowing technology improves grass lift and guarantees an even cut, while the deck wash port allows for easy cleaning of the mower deck after use. The ergonomic steering wheel and comfortable seat reduce operator fatigue, even during extended mowing sessions.

Additionally, the YTH2454T features an integrated mulching capability, enabling the mower to finely chop grass clippings and return them to the lawn, enriching the soil and promoting healthy growth. The easy-access controls make it user-friendly, ensuring that both novice and experienced users can operate it with ease.

With a tight turning radius of 16 inches, the Husqvarna YTH2454T excels in maneuverability, allowing it to navigate around landscaping, trees, and flower beds with minimal effort. This combination of power, comfort, and advanced features makes the YTH2454T a top choice for homeowners looking for a reliable and efficient riding mower. Whether maintaining a sprawling lawn or tackling rough terrain, the Husqvarna YTH2454T proves to be an excellent investment for achieving a beautifully manicured yard.
Top Page Image Contents