Husqvarna YTH2648TDRF Service And Adjustments, TO REMOVE MOWER See Fig, TO INSTALL MOWER See Fig

Page 20
SERVICE AND ADJUSTMENTS

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Depress brake pedal fully and set parking brake.

Place attachment clutch in “DISENGAGED” position.

Turn ignition key to “STOP” and remove key.
Make sure the blades and all moving parts have completely stopped.

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 22)

Place attachment clutch in “DISENGAGED” position.

Lower attachment lift lever to its lowest position.

Remove mower belt from electric clutch pulley (M). See Mower Drive Belt Removal in "TO REPLACE MOWER BLADE DRIVE BELT" in this section.

Disconnect front link (E) from mower - remove retainer spring and washer.

Go to either side of mower and disconnect mower suspension arm (A) from chassis and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

Go to other side of mower and disconnect the suspen- sion arm and rear lift link.

CAUTION: After rear lift links are discon- nected, the attachment lift lever will be spring loaded. Have a tight grip on lift lever when changing position of the lever.

Slide mower out from under right side of tractor.

TO INSTALL MOWER (See Fig. 22-29)

Ensure tractor is on level surface and engage parking brake.

Lower attachment lift lever to its lowest position.

CAUTION: Lift lever is spring loaded. Have a tight grip on lift lever, lower it slowly and engage in lowest position.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

Slide mower under tractor until it is centered under tractor.

INSTALL ANTI-SWAY BAR (S) (IF EQUIPPED)

ANTI-SWAY BAR (S)

TOWARDS

TOWARDS

TRANSAXLE

MOWER DECK

90° END

INTEGRATED WASHER END

Fig. 23

A

C

D

C

D

M•Depress brake pedal fully and set parking brake.•Place attachment clutch in “DISENGAGED” position.•Turn ignition key to “STOP” and remove key.•Make sure the blades and all moving parts have completely stopped. F O P

Q

E

H

B

Fig. 22

20

Image 20
Contents YTH2648TDRF Owners Manual532 44 40-19 Rev 07002SAFETY RULES Safe Operation Practices for Ride-On MowersSAFE HANDLING OF GASOLINE III. CHILDRENGENERAL SERVICE TABLE OF CONTENTS PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES SERVICE AND ADJUSTMENTSASSEMBLY TOOLS REQUIRED FOR ASSEMBLYTO CHECK BATTERY See Fig ADJUST SEAT See FigCHECK TIRE PRESSURE CHECK DECK LEVELNESSCHECK FOR PROPER POSITION OF ALL BELTS CHECK BRAKE SYSTEMOPERATION KNOW YOUR TRACTOR HOW TO USE YOUR TRACTOR TO SET PARKING BRAKESee FigSTOPPING See Fig TO USE THROTTLE CONTROL D See Fig.6TO ADJUST MOWER CUTTING HEIGHT See Fig TO ADJUST GAUGE WHEELS See FigTO MOVE FORWARD AND BACKWARD See Fig K J LSERVICE REMINDER/HOUR METER TO STOP MOWER BLADESREVERSE OPERATION SYSTEM ROS TO OPERATE ON HILLSBATTERY INDICATOR/CHARGING PLUG See Fig BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL ADD GASOLINETO START ENGINE See Fig PURGE TRANSMISSIONMOWING TIPS MAINTENANCE MAINTENANCEGENERAL RECOMMENDATIONS SCHEDULEBATTERY TRACTORBLADE CARE BLADE REMOVAL See FigTRANSAXLE MAINTENANCE ENGINEV-BELTS TRANSAXLE PUMP FLUIDCLEANING CLEAN AIR SCREENAIR FILTER ENGINE COOLING SYSTEMDECK WASHOUT PORT See Fig PluganyholesinmowerwithboltsandlocknutsSERVICE AND ADJUSTMENTS TO INSTALL MOWER See FigTO REMOVE MOWER See Fig A C D C DSERVICE AND ADJUSTMENTS TO LEVEL MOWER TO REPLACE MOWER BLADE DRIVE BELT TO CHECK BRAKEIDLER ARM BELT ROUTING ENGINE BLADE BELTTO START ENGINE WITH A WEAK BATTERY See Fig TO REPLACE MOTION DRIVE BELT See FigFRONT WHEEL TOE-IN/CAMBER TO REMOVE WHEEL FOR REPAIRS See FigREPLACING BATTERY See Fig TO REMOVE HOOD AND GRILL ASSEMBLY See FigREMOVAL/REPLACEMENT TO ADJUST THROTTLE CONTROL CABLESTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING PROBLEMCAUSE CORRECTIONEngine continues to SERVICE NOTES TRACTOR - MODEL NO. YTH2648TDRF 96041026400, PRODUCT NO. 960 DECALSWHEELS AND TIRES KEY PARTSCHEMATIC TRACTOR - MODEL NO. YTH2648TDRF 96041026400, PRODUCT NO. 960 41PTO SWITCH IGNITION SWITCHTRACTOR - MODEL NO. YTH2648TDRF 96041026400, PRODUCT NO. 960 41 ELECTRICALWith Service Minder Option With Charge Indicator OptionPART CHASSIS chassis-texGT HUSQ II94r1TRACTOR - MODEL NO. YTH2648TDRF 96041026400, PRODUCT NO. 960 41 DRIVE drive-texK46pedal71r3532 13 Spacer SplitSPARK ARRESTER KIT ENGINEEngine Power Rating Information STEERING ASSEMBLY steering-texTTR7Axle Asm., Front Seat SEAT ASSEMBLY532 44 MOWER LIFT              MOWER DECK 48Felec-Tex5TRACTOR - MODEL NO. YTH2648TDRF 96041026400, PRODUCT NO. 960 41 MOWER DECKPART DESCRIPTIONSERVICE NOTES ONLY RIDE UP AND DOWN HILL NOT ACROSS HILL 15 DEGREES MAX SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION04.02.13 JM Printed in the U.S.A