Husqvarna YTH2246 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain

conditions.10

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG.9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place.

S

FIG. 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH2246 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyCheck Battery To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS onHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission To Start Engine See FigAutomatic Transmission Warm UP Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH2246 96043003700, Product no 43Electrical KEY Part NO. NO. Description Chassis Tractor - Model Number YTH2246 96043003700, Product no 43 Drive KEY Part Description Steering Assembly Engine 30!2+ª!22%34%2ª+4Seat Assembly Decals Wheels and TiresMower Deck Tractor - Model Number YTH2246 96043003700, Product no 43 Mower Lift Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 05-33 11.27.06 TH

YTH2246 specifications

The Husqvarna YTH2246 is a robust and efficient riding lawn mower designed to tackle both residential and light commercial mowing tasks. With its impressive blend of power, comfort, and innovation, this lawn tractor has gained a reputation for quality and reliability among homeowners and landscapers alike.

One of the standout features of the YTH2246 is its powerful 22 horsepower Briggs & Stratton engine. This reliable engine provides ample power to handle a variety of mowing conditions, ensuring that the mower can easily cut through thick grass and tackle uneven terrain. The engine is designed with a hydrostatic transmission, which allows for smooth acceleration and effortless operation. This transmission system eliminates the need for complex gear shifting, making it easier for users to focus on mowing while enjoying a comfortable ride.

The cutting deck of the YTH2246 is another significant characteristic, with a 46-inch cutting width that allows for efficient mowing over larger areas. The reinforced steel construction ensures durability, while the innovative cutting system provides an even and precise cut. Additionally, the deck features a convenient deck washout port, making cleaning the underside of the mower a straightforward task.

Comfort is paramount in the design of the YTH2246. It is equipped with an ergonomic high-back seat that provides ample support for long mowing sessions. The mower's steering wheel is positioned to provide an intuitive and comfortable grip, enhancing maneuverability. Also, the large front and rear tires enhance traction and stability, allowing the mower to navigate challenging landscapes without compromising performance.

Another noteworthy technology included in the YTH2246 is the engineered cutting system that optimizes airflow, allowing for better grass lifting and a more efficient cut. With the option to set different cutting heights, users can customize their mowing experience to suit their lawn's specific needs.

In summary, the Husqvarna YTH2246 combines power, comfort, and innovative technology to deliver an exceptional mowing experience. Its robust engine, responsive hydrostatic transmission, generous cutting deck, and comfortable design make it an ideal choice for maintaining lush lawns with ease and efficiency. Whether you’re a professional landscaper or a dedicated homeowner, the YTH2246 is engineered to help you achieve a well-manicured lawn effortlessly.
Top Page Image Contents