Husqvarna YTH2246 owner manual Check Tire Pressure, Check Deck Levelness, Check Brake System

Page 6

ASSEMBLY

•Release parking brake by depressing brake pedal.

•Place freewheel control in disengaged position to dis- engage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START" in the Operation section of this manual). After engine has started, move throttle control to idle (slow) position.

•Release parking brake.

•Slowly depress forward drive pedal and drive tractor off skid.

•Apply brake to stop tractor and set parking brake.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is operating properly. See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.

✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PER- FORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓All assembly instructions have been completed.

✓No remaining loose parts in carton.

✓Battery is properly prepared and charged.

✓Seat is adjusted comfortably and tightened securely.

✓All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

✓Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

✓Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

✓Check wiring. See that all connections are still secure and wires are properly clamped.

✓Before driving tractor, be sure freewheel control is in “transmission engaged” position (see “TO TRANS- PORT” in the Operation section of this manual).

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

✓Engine oil is at proper level.

✓Fuel tank is filled with fresh, clean, regular unleaded gasoline.

✓Become familiar with all controls, their location and function. Operate them before you start the engine.

✓Be sure brake system is in safe operating condition.

✓Be sure Operator Presence System and Reverse Op- eration System (ROS) are working properly (See the Operation and Maintenance sections in this manual).

✓It is important to purge the transmission before oper- ating your tractor for the first time. Follow proper start- ing and transmission purging instructions (See “TO START ENGINE” and “PURGE TRANSMISSION” in the Operation section of this manual).

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents YTH2246 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyCheck Battery To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS onHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH2246 96043003700, Product no 43Electrical KEY Part NO. NO. Description Chassis Tractor - Model Number YTH2246 96043003700, Product no 43 Drive KEY Part Description Steering Assembly Engine 30!2+ª!22%34%2ª+4Seat Assembly Decals Wheels and TiresMower Deck Tractor - Model Number YTH2246 96043003700, Product no 43 Mower Lift Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 05-33 11.27.06 TH

YTH2246 specifications

The Husqvarna YTH2246 is a robust and efficient riding lawn mower designed to tackle both residential and light commercial mowing tasks. With its impressive blend of power, comfort, and innovation, this lawn tractor has gained a reputation for quality and reliability among homeowners and landscapers alike.

One of the standout features of the YTH2246 is its powerful 22 horsepower Briggs & Stratton engine. This reliable engine provides ample power to handle a variety of mowing conditions, ensuring that the mower can easily cut through thick grass and tackle uneven terrain. The engine is designed with a hydrostatic transmission, which allows for smooth acceleration and effortless operation. This transmission system eliminates the need for complex gear shifting, making it easier for users to focus on mowing while enjoying a comfortable ride.

The cutting deck of the YTH2246 is another significant characteristic, with a 46-inch cutting width that allows for efficient mowing over larger areas. The reinforced steel construction ensures durability, while the innovative cutting system provides an even and precise cut. Additionally, the deck features a convenient deck washout port, making cleaning the underside of the mower a straightforward task.

Comfort is paramount in the design of the YTH2246. It is equipped with an ergonomic high-back seat that provides ample support for long mowing sessions. The mower's steering wheel is positioned to provide an intuitive and comfortable grip, enhancing maneuverability. Also, the large front and rear tires enhance traction and stability, allowing the mower to navigate challenging landscapes without compromising performance.

Another noteworthy technology included in the YTH2246 is the engineered cutting system that optimizes airflow, allowing for better grass lifting and a more efficient cut. With the option to set different cutting heights, users can customize their mowing experience to suit their lawn's specific needs.

In summary, the Husqvarna YTH2246 combines power, comfort, and innovative technology to deliver an exceptional mowing experience. Its robust engine, responsive hydrostatic transmission, generous cutting deck, and comfortable design make it an ideal choice for maintaining lush lawns with ease and efficiency. Whether you’re a professional landscaper or a dedicated homeowner, the YTH2246 is engineered to help you achieve a well-manicured lawn effortlessly.
Top Page Image Contents