Husqvarna YTH2246 To Check Brake, Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 22

SERVICE AND ADJUSTMENTS

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 28

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WEAK OR DEAD

 

 

FULLY CHARGED

BATTERY

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH2246 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyCheck Battery To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS onHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission To Start Engine See FigAutomatic Transmission Warm UP Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH2246 96043003700, Product no 43Electrical KEY Part NO. NO. Description Chassis Tractor - Model Number YTH2246 96043003700, Product no 43 Drive KEY Part Description Steering Assembly Engine 30!2+ª!22%34%2ª+4Seat Assembly Decals Wheels and TiresMower Deck Tractor - Model Number YTH2246 96043003700, Product no 43 Mower Lift Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 05-33 11.27.06 TH

YTH2246 specifications

The Husqvarna YTH2246 is a robust and efficient riding lawn mower designed to tackle both residential and light commercial mowing tasks. With its impressive blend of power, comfort, and innovation, this lawn tractor has gained a reputation for quality and reliability among homeowners and landscapers alike.

One of the standout features of the YTH2246 is its powerful 22 horsepower Briggs & Stratton engine. This reliable engine provides ample power to handle a variety of mowing conditions, ensuring that the mower can easily cut through thick grass and tackle uneven terrain. The engine is designed with a hydrostatic transmission, which allows for smooth acceleration and effortless operation. This transmission system eliminates the need for complex gear shifting, making it easier for users to focus on mowing while enjoying a comfortable ride.

The cutting deck of the YTH2246 is another significant characteristic, with a 46-inch cutting width that allows for efficient mowing over larger areas. The reinforced steel construction ensures durability, while the innovative cutting system provides an even and precise cut. Additionally, the deck features a convenient deck washout port, making cleaning the underside of the mower a straightforward task.

Comfort is paramount in the design of the YTH2246. It is equipped with an ergonomic high-back seat that provides ample support for long mowing sessions. The mower's steering wheel is positioned to provide an intuitive and comfortable grip, enhancing maneuverability. Also, the large front and rear tires enhance traction and stability, allowing the mower to navigate challenging landscapes without compromising performance.

Another noteworthy technology included in the YTH2246 is the engineered cutting system that optimizes airflow, allowing for better grass lifting and a more efficient cut. With the option to set different cutting heights, users can customize their mowing experience to suit their lawn's specific needs.

In summary, the Husqvarna YTH2246 combines power, comfort, and innovative technology to deliver an exceptional mowing experience. Its robust engine, responsive hydrostatic transmission, generous cutting deck, and comfortable design make it an ideal choice for maintaining lush lawns with ease and efficiency. Whether you’re a professional landscaper or a dedicated homeowner, the YTH2246 is engineered to help you achieve a well-manicured lawn effortlessly.
Top Page Image Contents