Husqvarna YTH2246 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 17)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Roll belt off engine pulley (M) and belt keepers (G).

•Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

•Remove clutch cable spring (Q) from idler arm (R).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

•Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE

MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C)FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Fig. 17-21)

Be sure tractor is on level surface and engage parking brake.

•Lower attachment lift lever to it's lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

•Slide mower under tractor until it is centered under tractor.

•ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring.

•Repeat on opposite side of tractor.

G M F

Q RG

A E

B

P C

K

L

D

 

 

 

FIG. 17

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents YTH2246 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyCheck Battery To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS onHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model Number YTH2246 96043003700, Product no 43Electrical KEY Part NO. NO. Description Chassis Tractor - Model Number YTH2246 96043003700, Product no 43 Drive KEY Part Description Steering Assembly Engine 30!2+ª!22%34%2ª+4Seat Assembly Decals Wheels and TiresMower Deck Tractor - Model Number YTH2246 96043003700, Product no 43 Mower Lift Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 05-33 11.27.06 TH

YTH2246 specifications

The Husqvarna YTH2246 is a robust and efficient riding lawn mower designed to tackle both residential and light commercial mowing tasks. With its impressive blend of power, comfort, and innovation, this lawn tractor has gained a reputation for quality and reliability among homeowners and landscapers alike.

One of the standout features of the YTH2246 is its powerful 22 horsepower Briggs & Stratton engine. This reliable engine provides ample power to handle a variety of mowing conditions, ensuring that the mower can easily cut through thick grass and tackle uneven terrain. The engine is designed with a hydrostatic transmission, which allows for smooth acceleration and effortless operation. This transmission system eliminates the need for complex gear shifting, making it easier for users to focus on mowing while enjoying a comfortable ride.

The cutting deck of the YTH2246 is another significant characteristic, with a 46-inch cutting width that allows for efficient mowing over larger areas. The reinforced steel construction ensures durability, while the innovative cutting system provides an even and precise cut. Additionally, the deck features a convenient deck washout port, making cleaning the underside of the mower a straightforward task.

Comfort is paramount in the design of the YTH2246. It is equipped with an ergonomic high-back seat that provides ample support for long mowing sessions. The mower's steering wheel is positioned to provide an intuitive and comfortable grip, enhancing maneuverability. Also, the large front and rear tires enhance traction and stability, allowing the mower to navigate challenging landscapes without compromising performance.

Another noteworthy technology included in the YTH2246 is the engineered cutting system that optimizes airflow, allowing for better grass lifting and a more efficient cut. With the option to set different cutting heights, users can customize their mowing experience to suit their lawn's specific needs.

In summary, the Husqvarna YTH2246 combines power, comfort, and innovative technology to deliver an exceptional mowing experience. Its robust engine, responsive hydrostatic transmission, generous cutting deck, and comfortable design make it an ideal choice for maintaining lush lawns with ease and efficiency. Whether you’re a professional landscaper or a dedicated homeowner, the YTH2246 is engineered to help you achieve a well-manicured lawn effortlessly.
Top Page Image Contents