Husqvarna ZEKW42170, ZEKW52210 manual Winter Storage, Service

Page 64

STORAGE

Storage

Winter Storage

At the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days). Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function.

Fuel stabilizers are an acceptable option as regards to the sticky residues that can occur during storage.

Add stabilizer to the fuel in the tank or in the storage container. Always use the mixing ratios specified by the manufacturer of the stabilizer. Run the engine for at least 10 minutes after adding the stabilizer so that it reaches the carburetor. Do not empty the fuel tank and the carburetor if you have added stabilizer.

WARNING!

Never store an engine with fuel in the tank indoors or in poorly ventilated spaces where fuel vapor can come in contact with open flames, sparks, or a pilot light such as in a boiler, hot water tank, clothes drier, etc. Handle the fuel with care. It is very flammable and careless use can cause serious personal injury and property damage. Drain the fuel into an approved container outdoors and far away from open flame. Never use gasoline for cleaning. Use a degreaser and warm water instead.

To ready the machine for storage, follow these steps:

1.Thoroughly clean the machine, especially under the mower deck. Touch up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion.

2.Inspect the machine for worn or damaged parts and tighten any nuts or screws that may have become loose.

3.Change the engine oil; dispose of properly.

4.Empty the fuel tanks or add a fuel stabilizer. Start the engine and allow it to run until the carburetor is drained of fuel or the stabilizer has reached the carburetor.

5.Remove the spark plug and pour about a tablespoon of engine oil into the cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plug.

6.Lubricate all grease zerks, joints, and axles.

7.Remove the battery. Clean, charge, and store the battery in a cool place, but protect it from direct cold.

8.Store the machine in a clean, dry place and cover it for extra protection.

Service

When ordering spare parts, please specify the purchase year, model, type, and serial number.

Always use genuine Yazoo/Kees spare parts.

An annual check-up at an authorized service workshop is a good way to ensure that your machine performs its best the following season.

English-62

Image 64
Contents Operator’s manual Models Page Contents OPERATOR’S Manual ZE RiderEnglish-2 Introduction IntroductionGood Service Manufacturing NumberSymbols and Decals Symbols and DecalsXxxx xxxxxx Repair work Safety Instructions Safety InstructionsGeneral Operation English-8 Personal Safety Equipment Slope OperationChildren Maintenance General Maintenance Risk of sparking Transport Important InformationCustomer responsibilities Controls ControlsMotion Control Levers Parking BrakeMachine must be stopped before activating the parking brake Tracking Seat adjustment boltsFuel Shut Off Valve Refueling By pass linkage FusesHour Meter Ignition SwitchChoke Control Blade switch Throttle ControlAccessories Cutting height pedalOperation OperationTraining Before Starting Starting the EngineDepress the control for disengaging the mower deck Set the choke control USE Full Throttle When Mowing To start an engine with a weak battery To remove cables, reverse orderRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule Nance Once Each Maintenance Before After 100 Battery To clean battery and terminalsReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Checking and Adjusting the Choke Cable Checking and Adjusting the Throttle CableChecking the Engines Cooling Air Intake Replacing the Air Filter Kawasaki Engine Checking the Fuel Pump’s Air Filter Replacing the Fuel FilterChecking Tire Pressures Faulty adjustment can cause an accident Checking the Parking BrakeChecking the V-belts Deck beltDeck belt installation Belt installation IZT beltTo replace IZT Integraded Zeroturn Transaxle belt IZT belt removalChecking the Blades Remove blade bolt by turning counterclockwise Adjusting Cutting Height Adjusting the Mower DeckLeveling To adjust anti-scalp rollers Cleaning and Washing Use protective glasses when cleaning and washingRemoval and installation of caster wheel Caster WheelsTracking adjustment To adjust parking brakeMower is tracking to the right Mower is tracking to the leftLubrication LubricationLubrication Schedule Change transaxles transmission filtersLubricating the Cables Lubricating in Accordance with the Lubrication ScheduleFront Wheel Mount Front Wheel BearingsDeck outer spindle Engine Oil Changing the Engine OilChecking the Oil Level Changing the Engine Oil Filter Transaxle Transmission Fluid ChangeExpansion Tank Purging Procedures Trouble Shooting Guide Trouble Shooting Guide Problem Cause English-60 English-61 Service StorageStorage Winter StorageWiring Diagrams Wiring diagramTechnical Data Technical DataZEKW42170/968999295 ZEKW52210/968999296 Productivity Torque Specifications Conformity Certificates Conformity CertificatesUSA requirements Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-71 English-72 English-73 At Least Once Each Year English-75 English-76 English-77