Invacare Top End Terminator Jr manuals

44 pages701.88 Kb

2SPECIAL NOTES
- TABLE OF CONTENTS
3TABLE OF CONTENTS
- 4
- TERMINATOR JR.
4SPECIFICATIONS
- P
- C
- F
- C
- T
- O N
- SPECIFICATIONS
  - NOTE: All specifications are approximate.
- 5STABILITY WARNING
  - NOTE: When changes to the left hand column occur, follow across the chart and refer to the
  - procedure to maintain the proper stability, safety and handling of the racing chair.
- GENERAL GUIDELINES
  - This Procedure includes the following: Operating Information Safety/Handling of Wheelchairs
- PROCEDURE 1
- 6SAFETY/HANDLING OF WHEELCHAIRS
  - F
  - T Y
  - U M M
  - R Y
  - GENERAL GUIDELINESPROCEDURE 1
  - 7GENERAL GUIDELINES PROCEDURE 1
    - Center of Gravity
  - Coping with Everyday Obstacles
  - A Note to Wheelchair Assistants
  - Stability and Balance
    - Telescoping Tube
  - Percentage of Weight Distribution
  - 8Reaching, Leaning - Backwards
  - GENERAL GUIDELINESPROCEDURE 1
  - Reaching, Leaning and Bending Forward
  - Tilting
  - Functional Reach From a Wheelchair
  - 9Stairways
  - Transferring to and From Other Seats
  - GENERAL GUIDELINES PROCEDURE 1
  - ESCALATORS? SORRY!
- 10SAFETY INSPECTION CHECKLIST
  - PROCEDURE 2
  - SAFETY INSPECTION
    - This Procedure includes the following: Safety Inspection Checklist
- 11TROUBLESHOOTING
- MAINTENANCE
  - PROCEDURE 4 BACK
- 12FOLDING/UNFOLDING THE BACK
  - Folding the Back
  - Unfolding the Back
- CHANGING THE BACK ANGLE (FIGURE 2)
- 13REPLACING STANDARD BACK UPHOLSTERY (FIGURE 4)
- ADJUSTING THE BACK HEIGHT (FIGURE 3)
  - PROCEDURE 4BACK
- 14REPLACING CUSTOM MANUAL ADJUSTABLE TENSION BACK UPHOLSTERY (FIGURE 5)
  - The Adjustable Tension Straps
  - The Back Upholstery Cover
  - Replacing Adjustable Tension Back Upholstery
  - BACKPROCEDURE 4
  - PROCEDURE 4BACK
- 15REPLACING THE SPREADER BAR
- REPLACING THE LOCKING MECHANISM IN THE BACK CANE
- 17USING CANTILEVER ARMS
- INSTALLING/REMOVING CANTILEVER ARMS (FIGURE 1)
  - Installing
  - Removing
- 18ADJUSTING CANTILEVER ARM HEIGHT (FIGURE 1)
- ADJUSTING CANTILEVER ARM ANGLE (FIGURES 2 AND 3)
  - Actuator
  - Cantilever Arm
  - Spring
  - Angled Portion of Locking Mechanism Locking Mechanism
- 19ARMREST PAD ADJUSTMENT/ REPLACEMENT (FIGURE 5)
  - Armrest Pad Adjustment
  - Armrest Pad Replacement
    - REAR Phillips Screw Cantilever Slide Tube FRONT Phillips Screw
    - Armrest Tube
- REPLACING/REPOSITIONING THE CANTILEVER ARM LOCKING MECHANISM (FIGURE 4)
  - NOTE: Inspect the spring and replace if necessary.
- 20INSTALLING T-ARM SOCKETS
- INSTALLING/REMOVING T-ARMS
  - Installing T-Arms
  - Removing T-Arms
- ADJUSTING THE T-ARMS
  - Adjusting T-Arm Height (FIGURE 8)
  - 21Adjusting T-Arm Depth (FIGURE 10)
  - Adjusting T-Arm Width (FIGURE 9)
  - Adjusting T-Arm Sockets (FIGURE 11)
- 22REPLACING THE T-ARM LOCKING LEVER (FIGURE 12)
  - SEAT PROCEDURE 6
- 23REPLACING SEAT PAN (FIGURE 1)
- ADJUSTING REAR SEAT HEIGHT
- ADJUSTING SEAT DEPTH (FIGURES 2 AND 3)
  - 24
  - 987654321
  - Rear--------Wheelchair-------Front
    - Use these mounting holes ONLY NEVER use these mounting holes for the back angle bracket
    - NEVER use this mounting hole for the back angle bracket
  - 24PROPER MOUNTING HOLES FOR BACK ANGLE BRACKET
  - SHORT FRAME LONG FRAME
    - FIGURE 3 - ADJUSTING SEAT DEPTH
  - SEAT PROCEDURE 6
- 25ADJUSTING SEAT WIDTH (FIGURE 4)
  - NOTE: Retain the attachment hardware for installa- tion of the NEW seat pan.
  - Hex Screws Coved Washers
  - Crossmember
  - Wheelchair Frame Front Mounting Hole
  - Rear Mounting Hole
  - SEAT PROCEDURE 6
- ADJUSTING FRONT SEAT-TO-FLOOR HEIGHT
  - Determining Frame Height (FIGURE 5)
    - Seat Rail Bottom of Caster Headtube
- 26SHORT FRAME SEAT-TO-FLOOR HEIGHTS
- LONG FRAME SEAT-TO-FLOOR HEIGHTS
  - 27ADJUSTING QUICK-RELEASE AXLES (FIGURE 2)
  - REMOVING/INSTALLING REAR WHEELS (FIGURE 1)
  - 28INSTALLING QUAD-RELEASE AXLES (FIGURE 3)
    - Removing Play From Rear Wheels
  - ADJUSTING QUAD-RELEASE HANDLES (FIGURE 4)
    - In and/or Out
  - (FIGURE 5)
    - Allen Screw Locknut
    - Handrim
  - 29OPENING/CLOSING CLAMPS
    - Camber Clamps
    - Receiver Tube Clamps
      - NOTE: The receiver tube clamps are used ONLY to adjust wheelbase length.
  - REPAIRING/REPLACING REAR WHEEL, TIRE/TUBE
  - 30ADJUSTING REAR WHEEL CAMBER
    - Adjusting Toe In/Toe Out (FIGURE 10)
  - 31DETERMINING/ADJUSTING TOE IN/TOE OUT
    - Determining Toe In/Toe Out (FIGURES 8 AND 9)
  - 32ADJUSTING WHEELBASE LENGTH (FIGURE 11)
  - 33REPLACING AXLE TUBE (FIGURE 13)
  - ADJUSTING WHEELBASE WIDTH (FIGURE 12)
  - 34REPOSITIONING THE AXLE TUBE (FIGURES 14 AND 15)
    - WHEELS
    - PROCEDURE 7
    - 35AXLE TUBE POSITIONS
  - 36REPOSITIONING/REPLACING FRONT CASTERS (FIGURE 14)
    - Replacing Front Casters
    - Repositioning Front Casters
  - ADJUSTING FRONT CASTER HEIGHT (FIGURE 15)
  - 37WHEEL LOCK ADJUSTMENT/ REPLACEMENT (FIGURE 16)
  - 38ADJUSTING/REPLACING FLIP-UP FOOTBOARD (FIGURE 1)
  - 39ANTI-TIPPER REPLACEMENT/ ADJUSTMENT (FIGURE 3)
  - ADJUSTING/REPLACING RIGID TUBULAR FOOTREST (FIGURE 2)
  - 40ELASTOMERS AND SUSPENSION
  - REPLACING FRONT ELASTOMERS
43LIMITED WARRANTY