Invacare Top End Terminator Jr AXLE TUBE POSITIONS

35

AXLE CLAMP TELESCOPING TUBE

POSITION HOLE TUBE HOLE POSITION

CENTER 3ASTANDARD

2B

AXLE CLAMP TELESCOPING TUBE

POSITION HOLE TUBE HOLE POSITION

UPPER 1BSTANDARD

2A

Telescoping Tube

Hole A

Hole B

FIGURE 15 - REPOSITIONING THE AXLE TUBE

DETAIL "B" - MOUNTING HOLE PATTERN

Hole 2

Hole 1

Camber

Clamp

Anti-Tip

Tube

AXLE TUBE POSITIONS

DETAIL "A" - REVERSING THE TELESCOPING TUBES

Telescoping Tube

STANDARD

POSITION

REVERSED

POSITION

Seat Rail

Seat Rail Clamp

Hex

Screw

Nut Nut Clamp

Telescoping Tube

Hex

Screw

Mounting Plate

Long End

Hole 3

AXLE CLAMP TELESCOPING TUBE

POSITION HOLE TUBE HOLE POSITION

CENTER 1AREVERSED

2B

Clamp Hole 3

Clamp Hole 2

Telescoping

Tube Hole B

Clamp Hole 2

Clamp Hole 1

Telescoping

Tube Hole A

Telescoping

Tube Hole B

NOTE: Right camber clamp and telescoping shown as viewed with the wheelchair's underside facing up.

AXLE CLAMP TELESCOPING TUBE

POSITION HOLE TUBE HOLE POSITION

LOWER 2AREVERSED

3B

Telescoping

Tube Hole A

Telescoping

Tube Hole B

Clamp Hole 2

Clamp Hole 1

Clamp Hole 3

Clamp Hole 2

Telescoping

Tube Hole A

Telescoping

Tube Hole B

WHEELS PROCEDURE 7

W

H

E

E

L

S

Telescoping

Tube Hole A

Contents

Main SPECIAL NOTES TABLE OF CONTENTS TABLE OF CONTENTS 4 TERMINATOR JR. SPECIFICATIONS P C F C STABILITY WARNING NOTE: When changes to the left hand column occur, follow across the chart and refer to the procedure to maintain the proper stability, safety and handling of the racing chair. GENERAL GUIDELINES SAFETY/HANDLING OF WHEELCHAIRS F T Y U M M R Y GENERAL GUIDELINES PROCEDURE 1 Center of Gravity Coping with Everyday Obstacles A Note to Wheelchair Assistants Stability and Balance Reaching, Leaning - Backwards GENERAL GUIDELINESPROCEDURE 1 Reaching, Leaning and Bending Forward Tilting Functional Reach From a Wheelchair Stairways Transferring to and From Other Seats GENERAL GUIDELINES PROCEDURE 1 ESCALATORS? SORRY! SAFETY INSPECTION CHECKLIST PROCEDURE 2 SAFETY INSPECTION This Procedure includes the following: Safety Inspection Checklist TROUBLESHOOTING MAINTENANCE PROCEDURE 4 BACK FOLDING/UNFOLDING THE BACK Folding the Back Unfolding the Back CHANGING THE BACK ANGLE (FIGURE 2) REPLACING STANDARD BACK UPHOLSTERY (FIGURE 4) ADJUSTING THE BACK HEIGHT (FIGURE 3) PROCEDURE 4BACK REPLACING CUSTOM MANUAL ADJUSTABLE TENSION BACK UPHOLSTERY (FIGURE 5) The Adjustable Tension Straps The Back Upholstery Cover Replacing Adjustable Tension Back Upholstery BACKPROCEDURE 4 REPLACING THE SPREADER BAR REPLACING THE LOCKING MECHANISM IN THE BACK CANE Page USING CANTILEVER ARMS INSTALLING/REMOVING CANTILEVER ARMS (FIGURE 1) Installing Removing ADJUSTING CANTILEVER ARM HEIGHT (FIGURE 1) ADJUSTING CANTILEVER ARM ANGLE (FIGURES 2 AND 3) Actuator Cantilever Arm Spring ARMREST PAD ADJUSTMENT/ REPLACEMENT (FIGURE 5) Armrest Pad Adjustment Armrest Pad Replacement REAR Phillips Screw Cantilever Slide Tube FRONT Phillips Screw Armrest Tube INSTALLING T-ARM SOCKETS INSTALLING/REMOVING T-ARMS Installing T-Arms Removing T-Arms ADJUSTING THE T-ARMS Adjusting T-Arm Depth (FIGURE 10) Adjusting T-Arm Width (FIGURE 9) Adjusting T-Arm Sockets (FIGURE 11) REPLACING THE T-ARM LOCKING LEVER (FIGURE 12) SEAT PROCEDURE 6 REPLACING SEAT PAN (FIGURE 1) ADJUSTING REAR SEAT HEIGHT ADJUSTING SEAT DEPTH (FIGURES 2 AND 3) 24 987654321 PROPER MOUNTING HOLES FOR BACK ANGLE BRACKET SHORT FRAME LONG FRAME FIGURE 3 - ADJUSTING SEAT DEPTH SEAT PROCEDURE 6 ADJUSTING SEAT WIDTH (FIGURE 4) NOTE: Retain the attachment hardware for installa- tion of the NEW seat pan. Hex Screws Coved Washers Crossmember Wheelchair Frame Front Mounting Hole SHORT FRAME SEAT-TO-FLOOR HEIGHTS LONG FRAME SEAT-TO-FLOOR HEIGHTS ADJUSTING QUICK-RELEASE AXLES (FIGURE 2) REMOVING/INSTALLING REAR WHEELS (FIGURE 1) INSTALLING QUAD-RELEASE AXLES (FIGURE 3) Removing Play From Rear Wheels ADJUSTING QUAD-RELEASE HANDLES (FIGURE 4) In and/or Out (FIGURE 5) OPENING/CLOSING CLAMPS Camber Clamps Receiver Tube Clamps NOTE: The receiver tube clamps are used ONLY to adjust wheelbase length. REPAIRING/REPLACING REAR WHEEL, TIRE/TUBE ADJUSTING REAR WHEEL CAMBER Adjusting Toe In/Toe Out (FIGURE 10) DETERMINING/ADJUSTING TOE IN/TOE OUT Determining Toe In/Toe Out (FIGURES 8 AND 9) ADJUSTING WHEELBASE LENGTH (FIGURE 11) REPLACING AXLE TUBE (FIGURE 13) ADJUSTING WHEELBASE WIDTH (FIGURE 12) REPOSITIONING THE AXLE TUBE (FIGURES 14 AND 15) WHEELS PROCEDURE 7 AXLE TUBE POSITIONS REPOSITIONING/REPLACING FRONT CASTERS (FIGURE 14) Replacing Front Casters Repositioning Front Casters ADJUSTING FRONT CASTER HEIGHT (FIGURE 15) WHEEL LOCK ADJUSTMENT/ REPLACEMENT (FIGURE 16) ADJUSTING/REPLACING FLIP-UP FOOTBOARD (FIGURE 1) ANTI-TIPPER REPLACEMENT/ ADJUSTMENT (FIGURE 3) ADJUSTING/REPLACING RIGID TUBULAR FOOTREST (FIGURE 2) ELASTOMERS AND SUSPENSION REPLACING FRONT ELASTOMERS Page Page LIMITED WARRANTY