QSC Audio CM16a manuals

Home Audio > Home Theater System

When we buy new device such as QSC Audio CM16a we often through away most of the documentation but the warranty. Very often issues with QSC Audio CM16a begin only after the warranty period ends and you may want to find how to repair it or just do some service work. Even oftener it is hard to remember what does each function in Home Theater System QSC Audio CM16a is responsible for and what options to choose for expected result. Fortunately you can find all manuals for Home Theater System on our side using links below.

QSC Audio CM16a Manual

40 pages2.74 Mb

2 WARNING
3T ABLE OF CONTENTS: CM16a
- 4Federal Communications Commission (FCC) Information
  - Explanation of Graphical Symbols
  - 1-
5Section 1:
- Note:
- series)
8Section 1:
- FUNCTIONAL LISTING, BLOCK DIAGRAM & DETAILED DESCRIPTIONS
- 11AUDIO FUNCTIONS
  - Normal
  - STANDBY
  - ON
  - Monitor Chain In
  - Monitor Module
  - Page
  - Audio Input
  - Paging Input Module.
- AUDIO MONITOR CHAIN FUNCTIONS
  - Polarity
  - Level Control, Mute
  - Level Control
- AMPLIFIER CONTROL FUNCTIONS
- 12AMPLIFIER MONITORING FUNCTIONS
- PAGING FUNCTIONS
- 13RS-232 PORT FUNCTIONS
  - Note-
- CONTACT CLOSURE I/O FUNCTIONS
  - RLY/TRIG IN
15Section 1:
- crossover
18Section 2:
- CONNECTING AC POWER
- Note!
- 19CONNECTING AUDIO INPUTS
- Terminal Block Connector Hints-
- Balanced connection is recommended for all inputs.
  - If unbalanced audio sources are used
- 20CONNECTING THE RLY OUT
- CONNECTING PAGE INPUT
- CONNECTING THE RLY/TRG IN
- CONNECTING THE MONITOR CHAIN IN/OUT
- ATTENTION!
- CONNECTING TO THE RS-232 PORT
- 21Refer to Section 3
  - CONNECTION TO 10BASE-T (network connection)
  - CONNECTING TO 4-CHANNEL AMPLIFIERS
  - CONNECTING TO 2-CHANNEL AMPLIFIERS
23Section 3:
- LED Indicators-
- -
- POWER LED
  - -
- DIAGNOSTIC LED
- NETWORK STATUS LEDs
- PORT CONNECTED LEDs-
  - LINK STATUS
  - RCV, XMT
  - Technical Services
24Section 3:
- NETWORK-
- AMPLIFIER SETUP-
  - Remember:
  - was
  - Operation
- CM16a OPERATION-
- START-UP BEHAVIOR AND PRESET OPERATING MODES-
- PRESETS-
  - The reason for not actively using Preset 0 is as follows:
25Section 3:
- MODE #2-
- MODE #1-
- MODE #3-
  - transition
26Section 3:
- PORT H
- 1- 2- 3-
- Hyper Terminal
- Hyper Terminal,
- Hyper Terminal
- Hyper Terminal
- HyperTerminal Icon
  - RS-232 Communications Procedure:
- 271)
- 2)
  - Hyper Terminal
  - Hyper Terminal
  - Hyper Termi- nal
- 285)
- 3)
- 4)
- 296)
- 7)
  - IP ADDRESS ASSIGNMENT-
31Section 3:
- FUSE REPLACEMENT
- - 33Input Signal Processing
  - Power amplifier output processing
  - 34Power amplifier management
  - Control room foldback monitoring
  - Contact closure inputs and outputs
  - 35General
  - Network Interface 10BASE-T
  - RS232 Port
36SECTION 5 :
38Section 6:
- On-Shore-
- Riacon-
- Phoenix-
- NOTE!
- RS-232 PINOUT: The diagram (right) shows the pin assignments for RS-232.
39Section 7: How to Contact QSC Audio Products

40 pages1.94 Mb

2 WARNING
3TABLE OF CONTENTS: CM16a
- EXPLANATION OF GRAPHICAL SYMBOLS
  - CAUTION
  - AVIS
  - VORSICHT
- EXPLICATION DES SYMBOLES GRAPHIQUES
- ERKLRUNG DER GRAPHISCHEN SYMBOLE
- 4Federal Communications Commission (FCC) Information
5Section 1:
- Note: In this manual, bold type (e.g.
- series)
6Section 1:
- PHYSICAL CHARACTERISTICS
  - this is not labeled on the panel
- FRONT PANEL
- REAR PANEL
8Section 1:
- FUNCTIONAL LISTING, BLOCK DIAGRAM & DETAILED DESCRIPTIONS
- 11AUDIO FUNCTIONS
  - Audio Input
  - STANDBY
  - ON
  - Monitor Module
  - Paging Input Module.
- AUDIO MONITOR CHAIN FUNCTIONS
  - Polarity
  - Level Control, Mute
  - Level Control
  - Moni- tor Chain In
- AMPLIFIER CONTROL FUNCTIONS
  - NOTE! The amplifier must be powered in order to respond to any commands issued by the CM16a
- 12AMPLIFIER MONITORING FUNCTIONS
- PAGING FUNCTIONS
- 13RS-232 PORT FUNCTIONS
- CONTACT CLOSURE I/O FUNCTIONS
14Section 1:
- Section 3: Operation
15Section 1:
- crossover
17Section 2:
- UNPACKING
- WHAT IS INCLUDED IN THE CARTON
- LOCATION CONSIDERATIONS
- MOUNTING THE CM16a
18Section 2:
- CONNECTING AC POWER
- 19CONNECTING AUDIO INPUTS
  - REAR PANEL- PAGE, RELAY & MONITOR CONNECTIONS
- 20CONNECTING THE MONITOR CHAIN IN/ OUT
- CONNECTING PAGE INPUT
- CONNECTING THE RLY/TRG IN
- CONNECTING THE RLY OUT
- 21CONNECTION TO 10BASE-T (network connection)
  - directly
  - Second
  - First
  - crossover
- CONNECTING TO THE RS-232 PORT
- CONNECTING TO AMPLIFIERS
24Section 3:
- AMPLIFIER SETUP-
  - Remember:
  - was
  - The reason for not actively using Preset #0 is as follows:
- NETWORK-
  - Initial Testing
- CM16a OPERATION- Turn the Power ON!
  - It is important to understand the start-up behavior outlined below.
25Section 3:
- LED BEHAVIOR-
- PORT CONNECTED LEDs-
  - Introduction
  - NETWORK STATUS LEDs
  - DIAGNOSTIC LED
  - POWER LED
- BYPASS SWITCH USE
  - disabled, 0 dB level, normal polarity
  - 1Vrms input sensitivity,
  - input disabled,
- (continued on next page)
  - -
26Section 3:
- FRONT PANEL- BYPASS SWITCH LOCATION
- 271)
- 2)
- 285)
- 3)
- 4)
- 296)
  - Hyper Terminal
- 7)
  - IP ADDRESS ASSIGNMENT-
30Section 3:
- Host Name:
- Type:
- Term
- (NOTE: Port:
31Section 3:
- FUSE REPLACEMENT
- - 33Input Signal Processing
  - Power amplifier output processing
  - 34Power amplifier management
  - Control room foldback monitoring
  - Contact closure inputs and outputs
  - 35General
  - Network Interface
  - RS232 Port
- 36SECTION 5:
38Section 6:
- On-Shore-
- Riacon-
- Phoenix-
- NOTE!
- RS-232 PINOUT: The diagram below shows the pin assignments for RS-232.
39Section 7: How to Contact QSC Audio Products

Also you can find more QSC Audio manuals or manuals for other Home Audio.