Manuals / Accton Technology / Computer Equipment / Switch

Accton Technology ES3628EA manual Installing an Optional SFP Transceiver

Models: ES3628EA

1 62

Download 62 pages 11.34 Kb

Page 36

Installing an Optional SFP Transceiver

3 Installing the Switch

3.If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order.

Installing an Optional SFP Transceiver

Figure 3-5 Inserting an SFP Transceiver into a Slot

This switch supports 100BASE-FX, 1000BASE-T, 1000BASE-SX, 1000BASE-LX, and 1000BASE-LH SFP transceivers. To install an SFP transceiver, do the following:

1.Consider network and cabling requirements to select an appropriate SFP transceiver type.

2.Insert the transceiver with the optical connector facing outward and the slot connector facing down. Note that SFP transceivers are keyed so they can only be installed in one orientation.

3.Slide the SFP transceiver into the slot until it clicks into place.

Note: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removing a transceiver. However, always first disconnect the network cable before removing a transceiver.

3-6

Image 36

Accton Technology ES3628EA manual Installing an Optional SFP Transceiver, 5 Inserting an SFP Transceiver into a Slot

Contents

ES3628EA 24 10/100 Ports + 4G L2/L3/L4 Intelligent Switch Installation GuidePage 24 10/100 Ports + 4G L2/L3/L4 Intelligent Switch Installation GuideLayer 3 Standalone Switch with 24 100BASE-TX RJ-45 Ports 2 1000BASE-T RJ-45 Ports, and 2 SFP SlotsES3628EA E112007-DT-R01 150200064200A FCC - Class A Industry Canada - Class AJapan VCCI Class A Compliances and Safety WarningsCE Mark Declaration of Conformance for EMI and Safety EEC Australia AS/NZS 3548 1995 - Class ASafety Compliance Power Cord SafetyWarning Fiber Optic Port Safety Warnhinweis Faseroptikanschlüsse - Optische SicherheitPower Cord Set France et Pérou uniquement 18, ouAWG No. 16 pour un cable de longueur inferieure a` 2 metresLe cordon doit être en mesure d’acheminer un courant nominal d’au La prise femelle de branchement doit être du type à mise à la terreWarnings and Cautionary Messages Warnings in GermanEnvironmental Statement PurposeRelated Publications The 24 10/100 Ports + 4G L2/L3/L4 Intelligent Switch Management GuidePage Contents Chapter 3 Installing the SwitchChapter 1 Introduction Chapter 2 Network PlanningAppendix A Troubleshooting Appendix C SpecificationsChapter 4 Making Network Connections Appendix B CablesTables Figures Switch Architecture Switching MethodChapter 1 Introduction OverviewDescription of Hardware Network Management Options100BASE-TX and 1000BASE-T Ports SFP SlotsStatus LEDs Figure 1-2 Port LEDs Table 1-1 Port Status LEDsCondition StatusOptional Redundant Power Supply Power Supply ReceptaclesRedundant Power Socket Figure 1-4 Power Supply ReceptaclesFeatures and Benefits ConnectivityExpandability Performance1 Introduction Introduction to Switching Chapter 2 Network PlanningApplication Examples Collapsed BackboneFigure 2-1 Collapsed Backbone Network Aggregation Plan Figure 2-2 Network Aggregation PlanRemote Connections with Fiber Cable Figure 2-3 Remote Connection with Fiber CableMaking VLAN Connections Figure 2-4 Making VLAN ConnectionsUsing Layer 3 Routing Figure 2-5 IP Routing for Unicast TrafficApplication Notes 2 Network Planning Chapter 3 Installing the Switch Selecting a SiteEthernet Cabling Equipment Checklist Package ContentsOptional Rack-Mounting Equipment RJ-45 ConnectorMounting Rack MountingTo rack-mount devices Figure 3-2 Attaching the BracketsRack-Montage Figure 3-3 Installing the Switch in a RackMontage Rack Mounting Instructions - German Desktop or Shelf Mounting Figure 3-4 Attaching the Adhesive FeetInstalling an Optional SFP Transceiver Figure 3-5 Inserting an SFP Transceiver into a SlotConnecting to a Power Source Figure 3-6 Power ReceptacleConnecting to the Console Port Wiring Map for Serial CableSerial Cable Wiring Figure 3-7 Serial Port DB-9 DTE Pin-OutConnecting Network Devices Connecting to PCs, Servers, Hubs and SwitchesChapter 4 Making Network Connections Twisted-Pair DevicesNetwork Wiring Connections Figure 4-2 Network Wiring ConnectionsFiber Optic SFP Devices Figure 4-3 Making LC Port ConnectionsConnectivity Rules 1000BASE-T Cable Requirements1000 Mbps Gigabit Ethernet Collision Domain ConnectorCable Labeling and Connection Records 100 Mbps Fast Ethernet Collision Domain10 Mbps Ethernet Collision Domain ConnectorDifferentiate between racks by naming accordingly Appendix A Troubleshooting Diagnosing Switch IndicatorsPower and Cooling Problems Diagnosing Power Problems with the LEDsInstallation In-Band AccessAppendix B Cables Twisted-Pair Cable and Pin Assignments10BASE-T/100BASE-TX Pin Assignments Figure B-1 RJ-45 Connector Pin NumbersStraight-Through Wiring Crossover WiringMDI Signal Name Figure B-2 Straight-through Wiring1000BASE-T Pin Assignments Figure B-3 Crossover WiringMDI Signal Name MDI-X Signal NameCable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling to Run 1000BASE-T1000BASE-T Cable Requirements Fiber StandardsAppendix C Specifications Physical CharacteristicsSwitching Database WeightSwitch Features Management FeaturesPower Supply Power ConsumptionStandards CompliancesSafety EmissionsC Specifications Glossary Glossary Glossary-2Separate LAN or collision domain Transmission Control Protocol/Internet Protocol TCP/IP Virtual LAN VLANIndex Index Index-2Page ES3628EA E112007-DT-R01 150200064200A