Sec1:28-Sec1:29
|
| ADDITIONAL INFORMATION | 5. | Take out the old battery and replace it with a new |
|
|
|
| |||
| Replacing the Battery |
| battery. Place the battery’s positive (+) terminal FACE |
| |
|
| UP while you install it into the pedometer. |
| ||
|
|
|
|
| |
| 1. | When the figures on the display start to blink, it is time | 6. | CAUTION: Please DO NOTTOUCH inner pedometer |
|
|
| to replace the battery. |
| parts, other than battery.Touching the sensor |
|
| 2. | The unit uses oneType CR2032 |
| mechanism may affect the accuracy of the pedometer. |
|
| 3. | Insert a coin into the slot at the bottom of the body | 7. | Reinstall the BATTERY HOLDING PLATE by tightening |
|
|
| case.Twist the coin to remove the front case. |
| the two screws. Put the case back together by matching |
|
| 4. | Locate the BATTERY HOLDING PLATE at the bottom |
| the top edges of the front case and back case together, |
|
|
| then pressing the bottom of the case together. If the |
| ||
|
| left corner of the inside case. Remove the plate by |
|
| |
|
|
| two halves don’t go together easily, check if the front |
| |
|
| loosening the two small screws with a small Phillips |
|
| |
|
|
| case is upside down! |
| |
|
| head screwdriver. |
|
| |
|
| 8. | Reset the CLOCK. WEIGHT, and STRIDE to restore all |
| |
|
|
|
| ||
| 28 |
|
| functions to your pedometer. |
|
|
|
| 29 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
Sec1:30-Sec1:31
| Changing the Unit of Measure | INDEX |
|
|
| |
|
|
|
| |||
| To change between English (feet, pounds) and metric units: | Battery, replacing |
|
| ||
| Clock, setting |
|
| |||
| 1. | Repeatedly press the yellow MODE button until display |
|
| ||
| Current day’s results, viewing |
|
| |||
|
| is in STEP mode. |
|
| ||
|
| Exiting setup mode | . . . . . . 13 |
|
| |
| 2. | S1: Press yellow S1 (MODE) button for 2 seconds to |
|
| ||
| Memory |
|
| |||
|
| enter SET mode. | Memory, resetting | . . . . . . 21 |
|
|
| 3. | S2: Press yellow S2 (MODE) button repeatedly until | Setting up pedometer | . . . . . |
|
|
|
| STRIDE setting flashes (there will be a line under “DIST”). | Speedometer | . . . . . . 22 |
|
|
| 4. | S3: Simultaneously press and hold the yellow S2 (MODE) | Stopwatch |
|
| |
| Stride Length, setting | . . . . |
|
| ||
|
| and S3 ▲ (MEMORY) buttons for at least 5 seconds.The |
|
| ||
|
| Timer |
|
| ||
|
| unit will shift to the other measurement system. |
|
| ||
|
| Unit of measure, changing. . . | . . . . . . 30 |
|
| |
| 5. | S4: Press and hold yellow S4 (MODE) button for |
|
| ||
| Wearing pedometer | . . . . . . 14 |
|
| ||
|
| 2 seconds to exit SET mode. |
|
| ||
| 30 | Weight, setting | . . . . . . . 8 | 31 |
| |
|
|
| ||||
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
