Installation Procedures ______________

Installation should be performed by competent professional in accordance with local, state, and country codes. In the absence of these codes, the installation must conform to applicable American National Standards: ANSI Z223.1- LATEST EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70-LATEST EDITION (National Electrical Code) or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-M91 (Natural Gas) or CAN/ CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General Installation and Gas Plumbing) or Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION (for Electrical Connections).

Location Requirements ______________

Before installing the dryer, be sure the location conforms to local, state, and country codes. In the absence of such codes or ordinances the location must conform with the National Fuel Gas Code ANSI.Z223.1 LATEST EDITION, or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-M91 (Natural Gas) or CAN/ CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General Installation and Gas Plumbing).

The dryer must be installed on a sound level floor capable of supporting its weight. Carpeting must be removed from the floor area that the dryer is to rest on.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Dryers installed in residential garages must be elevated 18-inches (45.72 cm) above the floor.

Provisions for adequate air supply must be provided as noted in this manual (refer to Fresh Air Supply Requirements section).

Clearance provisions must be made from combustible construction as noted in this manual (refer to Dryer Enclosure Requirements section).

Provisions must be made for adequate clearances for servicing and for operation as noted in this manual (refer to Dryer Enclosure Requirements section).

The dryer must be installed with a proper exhaust duct connection to the outside as noted in this manual (refer to Exhaust Requirements section).

The dryer must be located in an area where correct exhaust venting can be achieved as noted in this manual (refer to Exhaust Requirements section).

Important: The dryer should be located where a minimum amount of exhaust ducting will be necessary.

The dryer must be installed with adequate clearance for air openings into the combustion chamber.

Caution

!This dryer produces combustible lint and must be exhausted to the outdoors. Every 6

months, inspect the exhaust ducting and remove any lint buildup.

Important: The dryer must be installed in a location/ environment, which the ambient temperature remains between 40° F (4.44° C) and 130° F (54.44° C).

Unpacking/Setting Up ________________

Remove protective shipping material (i.e., plastic wrap and optional shipping box) from the dryer.

Important: Dryer must be transported and handled in an upright position at all times.

The dryer can be moved to its final location while still attached to the skid or with the skid removed. To remove the skid locate and remove the 2 bolts securing the base of the dryer to the wooden skid. One is located at the center rear and the other is at the center front.

With the skid removed, use caution and assure all four leveling legs are fully retracted, if the dryer is to be slid into its final position.

Leveling Dryer

The dryer is equipped with 4 leveling legs, 1 at each corner of the base. For optimum performance the dryer should be level front-to-back and side-to-side.

Dryer Enclosure Requirements _______

Commercial Type II

Bulkheads and partitions should be made of noncombustible material.

Note: Allowances must be made for opening the control door.

AThe requirement to allow the door to open completely is 40-inches (101.6 cm).

BA minimum overhead clearance of 6-inches (15.24 cm) is required.

CDryer should be positioned a minimum of 12-inches (30.48 cm) away from the nearest obstruction. 24-inches (60.96 cm) is recommended for ease of installation, maintenance, and service.

D1/16” (1.5875 mm) minimum is required.

EFlooring should be level or below dryer cabinet for ease of removing panels during maintenance.

FDryers may be positioned sidewall to sidewall, however a 1/16” (1.5875 mm) minimum allowance must be made for the opening and closing of the control door, along with the removal of panels during maintenance.

8

American Dryer Corp.

113615 -2

Page 7 Page 9
Page 8
Image 8
ADC HBG76 manual Installation Procedures, Location Requirements, Unpacking/Setting Up, Dryer Enclosure Requirements
Page 7 Page 9

HBG76 specifications

The ADC HBG76 is a state-of-the-art device designed for high-performance data acquisition and processing. It is primarily aimed at various applications in industries such as telecommunications, aerospace, military, and industrial automation. The HBG76's advanced features, robust technologies, and exceptional characteristics make it a standout choice for professionals requiring precise and reliable data handling.

One of the hallmark features of the HBG76 is its high-speed sampling capabilities. The ADC can handle sample rates exceeding 1 GSPS (giga samples per second), enabling it to capture rapid signal dynamics with exceptional fidelity. This capability is particularly valuable in applications where timing is crucial, such as radar systems or high-frequency trading in finance.

The HBG76 incorporates cutting-edge analog-to-digital conversion technology, ensuring that the signal integrity is maintained throughout the conversion process. With a resolution of up to 16 bits, the ADC delivers impressive accuracy and detail, facilitating high-quality signal representation. This feature is essential for applications requiring precise measurement and analysis of data.

Another significant aspect of the HBG76 is its versatility in connectivity options. The device supports various communication interfaces, including USB, Ethernet, and SPI, making it compatible with a wide range of systems. This flexibility allows users to integrate the ADC seamlessly into existing hardware setups, enhancing overall efficiency and ease of use.

In terms of power efficiency, the HBG76 is designed with advanced low-power technologies that optimize its energy consumption without compromising performance. This feature is particularly beneficial for battery-operated devices and remote applications where power availability may be limited.

The robust design of the HBG76 ensures longevity and reliability in demanding environments. Its rugged casing provides protection against dust, moisture, and temperature extremes, making it suitable for outdoor use and harsh industrial settings.

Overall, the ADC HBG76 stands out as a powerful tool for data acquisition and processing, boasting high-speed sampling, excellent resolution, versatile connectivity, energy efficiency, and durability. Whether in research laboratories, industrial monitoring, or advanced telecommunications systems, the HBG76 is engineered to meet the evolving needs of modern applications, driving innovation across diverse sectors.
Top Page Image Contents