Installation instructions

! CAUTION !

Because the compressor is located on the controls side of the unit (right side), this side will be heavier and more awkward to manipulate. Inadequate support on the control side of the unit can result in personal injury and damage to your unit and property. Therefore, it is recommended to have someone assist you during the installation of this unit.

F. Your unit was designed to evaporate condensation under normal conditions. However, under extreme humidity conditions, excess condensation may cause base pan to overflow to the outside.

The unit should be installed where condensation run-off cannot drip on pedestrians or neighboring properties.

1. Select the Best Location

A. Your room air conditioner was designed to

fit easily into a single or double hung window. However, since window designs vary, it may be necessary to make some modifications for safe and proper installation.

B. Make sure the window and frame are structurally sound and free from dry and rotted wood.

C. For maximum efficiency, install the air conditioner on the side of the house or building which favors more shade than sunlight. If the unit is in direct sunlight,

it is advisable to provide an awning over the unit.

D. Provide sufficient clearance around the cabinet to allow for ample air circulation through the unit. See (Fig.2). The rear of the unit should be outdoors and not in a garage nor inside of a building.

Keep unit as far away as possible from obstacles and obstructions and at least 30" above the floor or ground. Curtains and other objects within a room should be prevented from blocking the air flow.

 

 

Awning

20"

 

 

Min.

 

 

 

 

12" Min.

 

 

20"

 

 

Min.

 

 

Fence,

 

30" Min.

wall, or

Side

other

 

obstruction

 

obstacle.

Ground

 

 

 

Fig.2

 

Window opening requirements (see table below)

E. Be certain the proper electrical outlet is within reach of the installation. Use only a single outlet circuit rated at 15 amps. All wiring should be in accordance with local and national electrical codes.

Size

Model

5K

6K

 

 

 

Cabinet size

17.7" *12.4" *15.7"

18.5" *13.7" *17.7"

(W*H*D)

 

 

Min. Window

21"

22"

opening

 

 

Max. Window

35"

36"

opening

 

 

6

Page 6 Page 8
Page 7
Image 7
Admiral AAW-06CR1FHUE Installation instructions, Select the Best Location, Window opening requirements see table below
Page 6 Page 8

AAW-06CR1FHUE, AAW-05CR1FHUE, AAW-05CM1FHUE, AAW-06CM1FHUE specifications

Admiral AAW-06CR1FHUE, AAW-05CM1FHUE, AAW-06CM1FHUE, and AAW-05CR1FHUE represent advanced models in the realm of air defense systems, renowned for their cutting-edge features, technologies, and specifications. These systems are engineered to provide robust protection against aerial threats, blending innovation and effectiveness.

Starting with the AAW-06CR1FHUE, this model is distinguished by its dual-layered defense mechanism that integrates both long-range interception technologies and close-in systems. Its radar systems utilize phased-array technology, enabling rapid detection and tracking of multiple targets simultaneously. This model is equipped with state-of-the-art missile systems that boast high maneuverability and precision targeting capabilities, making it adept at countering diverse threats, from drones to ballistic missiles.

Meanwhile, the AAW-05CM1FHUE offers a variant focused on countering medium-altitude aerial threats. It incorporates an advanced sensor suite that enhances situational awareness, allowing for seamless integration with existing command and control frameworks. The AAW-05CM1FHUE's missile systems are optimized for speed and agility, featuring advanced propulsion technologies that enhance their range and response times.

The AAW-06CM1FHUE emphasizes adaptability, featuring modular system architecture that allows for rapid upgrades and customization based on operational requirements. This characteristic makes it suitable for various theaters, ensuring that military units have the flexibility to respond to evolving air threats. Its software-driven capabilities enhance decision-making processes, utilizing artificial intelligence to analyze and triage incoming threats effectively.

Lastly, the AAW-05CR1FHUE stands out for its cost-effectiveness and efficiency. It employs advanced targeting algorithms and an integrated communication architecture that reduces latency in threat response time. This model is particularly valued for its ability to operate in contested environments, employing electronic countermeasures to enhance survivability and diminish the effectiveness of enemy targeting systems.

Collectively, these models reflect a significant leap in air defense technology, integrating aspects such as AI, modularity, and advanced propulsion systems. Their sophisticated radar and sensor configurations, coupled with their precise interception capabilities, make the Admiral AAW series indispensable in modern military operations, ensuring a strategic edge in securing airspace against diverse aerial threats. As air defense needs continue to evolve, these systems represent a forward-thinking approach to national security and defense preparedness.
Top Page Image Contents