ADTRAN 3192 H2TU-C warranty Indications and Probable Causes, HDSL2 Deployment Guidelines

HDSL2 TROUBLESHOOTING GUIDE

Pricing and Availability	800.827.0807
Tech Support	800.726.8663
Return for Repair	256.963.8722

www.adtran.com 61222004L2-22A

INDICATIONS AND PROBABLE CAUSES

Front Panel or Circuit Parameters Indicate Abnormal Operation

Connect a terminal or PC to the RS-232 (DB-9) craft interface, located on the faceplate. The ter- minal must be VT100 or compatible and set for 1.2 to 19.2 kbps, 8 data bits, no parity, 1 stop bit, and no flow control. Select “3” from the ADTRAN HDSL2 Main Menu Screen and “2” from the Span Status Screen:

■Is signal quality fluctuating (this would occur when real-time mode is active)?

■Is ATTEN (pulse attenuation) > 30 dB?

■Are there any errors counting on the ES, SES, or UAS registers?

If the above conditions do not exist, the circuit should provide quality service; however, if any of the above conditions exist, cable problem or excessive loss situation is probable and more detailed cable testing should be done to verify all HDSL2 Loop Specifications are met. These conditions may also reflect intermittent cable faults or excessive noise impairments. If intermit- tent faults or noise impairments are suspected, select “5” from the HDSL2 Main Menu to review the Performance History Screen.

Front Panel Indications Under Normal Operation

DSL	● Green
DSX	● Green
ALM	● Off
LBK	● Off

Circuit Parameters Under Normal Operation

■LOSS ≤ 30 dB

■Good signal quality with no fluctuation

■All HDSL2 Deployment Guidelines are met

HDSL2 DEPLOYMENT GUIDELINES

■Cable pairs must be non-loaded

■Total bridged tap < 2.5 kft

■No single bridged tap > 2 kft

■196 kHz insertion loss ≤ 35 dB

■Pulse attenuation (loss on HDSL2 Span Status Screen) ≤ 30 dB

■Maximum loop resistance is 900 Ω

■Impulse noises < 50 dBrn as measured using a 50 kb filter

■Wideband noise ≤ 31 dBrn as measured using a 50 kb filter

For more information regarding deployment guidelines and applications, reference ADTRAN’s Supplemental Deployment Information for HDSL/HDSL2, P/N 61221HDSLL1-10.

HDSL2 Loopback Control Codes

Name	Code	Comments
Arming (In-band)	11000	Signal sent in-band or over ESF data link. HDSL2 elements in disarmed
Arming (ESF)	0001 0010 1111 1111	state make transition to armed state. Detection of either code results in
	(12 FF Hex)	Smartjack loopup, if NIU loopback is enabled.
Activation	1101 0011 1101 0011	Signal sent in-band. HDSL2 elements in armed state make transition to
(H2TU-C)	(D3D3 Hex)	loop-up state. Loop-up state timeout is programmable from the H2TU-C.
Activation	1100 0111 0100 0010
(H2TU-R)	(C742 Hex)
Deactivation	1001 0011 1001 0011	Signal sent in-band. HDSL2 element loopup state makes transition to
	(9393 Hex)	armed state.
Disarming (In-band)	11100	Signal sent in-band or over ESF data link. HDSL2 elements in any state
Disarming (ESF)	0010 0100 1111 1111	make transition to disarmed state.
	(24FF Hex)
Arming Time out	N/A	2 Hours
Loopup Time out	N/A	HDSL2 element in loopup makes transition to armed state.
		Programmable from H2TU-C: None, 20, 60, or 120 minutes.
Loopback Time out	1101 0101 1101 0110	Signal sent in-band. Sets Loopback Timeout to NONE. Timeout will
Override	(D5D6 Hex)	return to previous value when pattern is removed. Arming pattern
		(11000) must precede this pattern.
Span Power	0110 0111 0110 0111	Signal sent in-band. Disables span powering of remotes. Span power
Disable	(6767 Hex)	will return when pattern is removed. Arming pattern (11000) must
		precede this pattern.