Manuals / Advantech / Computer Equipment / Computer Hardware

Advantech PCA-6185 user manual Floppy Drive Connector CN3, Parallel Port CN4

Models: PCA-6185

1 114

Download 114 pages 57.71 Kb

Page 31

2.2 Floppy Drive Connector (CN3)

2.2 Floppy Drive Connector (CN3)

CN3

You can attach up to two floppy disk drives to the PCA-6185's onboard connector. You can use 3.5" (720 KB, 1.44/2.88 MB) drives.

The card comes with a 34-pin daisy-chain drive connector cable. On one end of the cable is a 34-pin flat-cable connector. On the other end are two sets of 34-pin flat-cable connector (usually used for 3.5" drives). The set on the end (after the twist in the cable) connects to the A: floppy drive.

The set in the middle connects to the B: floppy drive.

2.3 Parallel Port (CN4)

CN4

The parallel port is normally used to connect the CPU card to a printer. The PCA-6185 includes an onboard parallel port, accessed through a 26- pin flat-cable connector, CN4. The card comes with an adapter cable which lets you use a traditional DB-25 connector. The cable has a 26-pin connector on one end and a DB-25 connector on the other, mounted on a retaining bracket. The bracket installs at the end of an empty slot in your chassis, giving you access to the connector.

To install the bracket, find an empty slot in your chassis. Unscrew the plate that covers the end of the slot. Screw in the bracket in place of the

21

Chapter2

Image 31

Advantech PCA-6185 user manual Floppy Drive Connector CN3, Parallel Port CN4

Contents

PCA-6185 User’s ManualCopyright Advantech customer services A Message to the CustomerTechnical support Manual User’sPCA-6185 Product warranty Initial Inspection Contents Hardware ConfigurationConnecting Peripherals ChapterChapter Award BIOS Setup2.11.1 SCSI Setup PCI SVGA SetupLAN Configuration Onboard Security SetupPin Assignments Programming the Watchdog TimerAppendix A Appendix BCHAPTER Hardware Configuration1.1 Introduction Chapter 1 Hardware Configuration1.2 Features 1.3.3 Input/Output 1.3 Specifications1.3.1 System 1.3.2 Memory1.3.5 Ethernet LAN 1.3.6 Industrial features1.3.7 Mechanical and environmental specifications 1.3.4 VGA interfaceTable 1.2 Connectors 1.4 Jumpers and ConnectorsTable 1.1 Jumpers Chapter1 Table 1.2 ConnectorsFigure 1.1 Jumper and connecter locations 1.5 Board Layout Jumper and Connector LocationsPCA-6185 User’s Manual LAN LAN Figure 1.2 Daughter board layoutFigure 1.3 Daughter board extension I/Os Chapter1Note 3 The PCA-6185 does not support Wake-on-LAN feature 1.7.2 CMOS clear J1 1.6 Safety Precautions1.7 Jumper Settings 1.7.1 How to set jumpersKeep CMOS data 1-2 closed Clear CMOS data 2-3 closed default setting Table 1.3 CMOS clear J1PCA-6185 User’s Manual Table 1.5 CPU FSB Frequency setting 1.7.3 PCI bus type setting selection JP11.7.4 CPU FSB Frequency setting JP7 Table 1.4 PCI bus type setting selection1.8.2 Supplementary information about DIMMs 1.9 Memory Installation Procedures1.8 System Memory 1.8.1 Sample calculation DIMM memory capacity1.10 Cache Memory 1.11 CPU InstallationModule Vendor 1.12 RAM Module Approval List1.13 Gigabit LAN Card Approval List PCA-6185 User’s ManualCard Part No 1.14 RAID Card Approval ListChapter1 Card VendorPCA-6185 User’s Manual CHAPTER Connecting Peripherals2.1 Primary CN1 and Secondary CN2 IDE Connec- tors Chapter 2 Connecting Peripherals2.3 Parallel Port CN4 2.2 Floppy Drive Connector CN32.4 USB Ports CN6/CN26 2.5 VGA Connector CN7CN26 2.7 Serial Ports CN9 COM1 CN10 COM2 2.6 10/100/1000Base-T Ethernet CN8 and CN342.9 External Keyboard Connector CN12 2.8 PS/2 Keyboard and Mouse Connectors CN112.10 CPU Fan Connector CN14 2.11.1 Power LED CN16 2.11 Front Panel Connectors CN16, 17, 18, 19, 21&222.11.2 External speaker CN17 2.11.3 Reset CN182.11.4 HDD LED CN19 CPU Card 2.11.5 SM Bus Connector CN292.11.6 Connecting to SNMP-1000 remote manager 2.11.7 ATX Power Control Connectors CN20 andIf you will not be using an ATX power connector This chapter describes how to set the card’s BIOS configuration data Award BIOS SetupCHAPTER 3.1 Introduction Chapter 3 Award BIOS Setup3.1.1 CMOS RAM auto-backup and restore to replace the battery in your systemFigure 3.1 Award BIOS Setup initial screen 3.2 Entering SetupFigure 3.2 Standard CMOS features screen 3.3 Standard CMOS SetupPCA-6185 User’s Manual Figure 3.3 Advanced BIOS features 3.4 Advanced BIOS Features3.4.1.2 Swap Floppy Drive 3.4.1 Boot Seq & Floppy SetupFigure 3.4 Boot sequence 3.4.1.3 Boot UP Floppy Seek3.4.2.4 Agent After Boot 3.4.3 Cache Setup3.4.2 Console Redirection Figure 3.5 Console Redirection3.4.10 Typematic Delay msec 3.4.6 Quick Power On Self Test3.4.7 Boot Up NumLock Status 3.4.8 Typematic Rate SettingChapter3 3.4.12 OS Select for DRAM 64MB3.4.13 MPS Version Control for OS It is recommended to keep the setting as defaultFigure 3.6 Advanced chipset features screen 3.5 Advanced Chipset Features3.5.1 System BIOS Cacheable DRAM default timings have been carefully chosenFigure 3.7 Integrated peripherals 3.6.1 IDE Funtion Setup3.6 Integrated Peripherals 3.5.3 Scrubbing3.6.2.6 ECP Mode Use DMA 3.6.2 Super I/O Function Setup3.6.3 Onboard Devices 3.6.2.5 Parallel Port Mode ECP + EPPFigure 3.8 Power management setup screen 3.7 Power Management Setup3.7.1 Power-supply Type 3.7.2 Power Management3.7.3 Video Off Method 3.7.4 Video Off In Suspend 3.8 PnP/PCI Configurations3.8.1 PnP OS Installed Figure 3.9 PnP/PCI configurations screen3.8.3 Resources controlled by 3.8.2 Reset Configuration Data3.9.1 CPU Warning Temperature 3.9 PC Health Status3.9.3 Current CPU Temperature 3.10 Load Setup Defaults3.11 Password Setting 3.9.2 Current System Temperature3.13 Exit Without Saving 3.12 Save & Exit SetupCHAPTER PCI SVGA Setuppressed. Do not attempt to install the drivers by Chapter 4 PCI SVGA Setup4.2 Features The files on the software installation CD are com4.3 VGA Installation PCA-6185 User’s Manual In the license window, click on Yes to continueClick on Yes The installaion is complete click on Yes to restart the systemChapter4 PCA-6185 User’s Manual CHAPTER LAN ConfigurationOperating system vendors may post driver updates Chapter 5 LAN Configuration5.2 Features 5.3 Driver InstallationChapter5 5.4 Windows NT Drivers Broadcom 5703/4 ProcedureNote The CD-ROM drive is designated as D throughout 2. In the Network window, select the Adapters tab. Then click on Add3. In the Select Network Adapter window, click on Have Disk 6. In the Microsoft TCP/IP Properties window, select the IP Address tab. Then select Specify an IP address. Type in the IP Address and Subnet Mask details. Then click on OK PCA-6185 User’s Manual 5.5 Windows 2000 Drivers Broadcom 5703/4 Proce- dureNote The CD-ROM drive is designed as D throughout this sec- tion 2. In the System Properties window, select the Device ManagerChapter5 4. In the following screen, to click on Update Driver7. Select Network adapter and then click Next 5. Click on Next 6. Following the highlighted item, and click on NextPCA-6185 User’s Manual Chapter5 8. Click on Have Disk9. Key in D\DrvLan\BROD57034\Windows2000\Driver, then click on OK 10. To highlight the following item, and click Next13. Click “Finish” to complete the installation 11. Click Next 12. Press Yes to continue the installationPCA-6185 User’s Manual CHAPTER Onboard Security Setup6.2 Installation Chapter 6 Onboard Security Setup6.1 Introduction Windows XP/2000 Drivers Setup Procedure 6.3 Windows XP/2000Chapter6 2. Click on OK to install OBS driver CHAPTER SCSI SetupIf any peripheral is running at SE mode, the Ultra Chapter 7 SCSI Setup7.1 Introduction 7.2 Understanding SCSIChapter7 7.3 SCSI IDsThe default settings are appropriate for most sys 7.5 Configuring the SCSI interface with SCSISelect7.4 Terminating the SCSI bus Available Settings Available SettingsDefault Settings Boot Device Optionstoggle between color and monochrome modes. This feature maye not work on some monitors7.6 Starting SCSISelect If you have difficulty viewing the display, press F5 toSCSI Device Configuration 7.7 Using SCSISelect SettingsTo configure settings for a SCSI device, you must know it’s SCSI IDDo not change the Advanced Configuration Options Set Initiate Wide Negotiation to NO if you are usingformance problems with 16-bit data transfer rate enabledExtended BIOS Translation for DOS Drives 1 GByte-Default Enabled When set to Enabled, provides an extended translation scheme for SCSI hard disks with capacities greater than 1 GByte. This setting is necessary only for MS-DOS 5.0 or above it is not required for other operating systems, such as NetWare of UNIX Support Removable Disks Under BIOS as Fixed Disks-Default Disabled Determines which removable-media drives are supported by the SCSI card BIOS. Choices are as follows 7.9 Installation under Windows NT/Windows 7.8 Using SCSI Disk Utilities7.10 Windows 2000 Driver setup procedure Chapter7 3. Click on “Update Driver”PCA-6185 User’s Manual 4. Click on “Next” 5. Recommend to serach for a better driverChapter7 7. The installation is completed. Click on “Finish.”8. Click on “Yes” to restart the system 7.11 Windows NT Driver Setup ProcedurePCA-6185 User’s Manual Chapter7 3. Click on “Have Disk.”PCA-6185 User’s Manual 5. Click the SCSI driver, and then click “OK.”Chapter7 6. The installation of SCSI Driver is completed. Click on “OK.”PCA-6185 User’s Manual Appendix Programming the Watchdog TimerA.1 Programming the Watchdog Timer Appendix A Programming the Watchdog TimerAppendixA PCA-6185 User’s Manual Appendix Pin AssignmentsPCA-6185 User’s Manual B.1 IDE Hard Drive Connector CN1, CN2Appendix B Pin Assignments Table B.1 IDE hard drive connector CN1, CN2AppendixB B.2 Floppy Drive Connector CN3Table B.2 Floppy drive connector CN3 low activeTable B.3 Parallel port connector CN4 B.3 Parallel Port Connector CN4PCA-6185 User’s Manual Table B.5 VGA connector CN7 B.4 USB Connector CN6B.5 VGA Connector CN7 Table B.4 USB1/USB2 connector CN6Table B.7 External keyboard connector CN12 B.7 External Keyboard Connector CN12B.6 Keyboard and Mouse Connnector CN11 Table B.6 Keyboard and mouse connector CN11Table B.9 Power LED CN16 B.8 CPU Fan Power Connector CN14B.9 Power LED CN16 Table B.8 CPU fan power connector CN14Table B.10 External speaker CN17 B.10 External Speaker Connector CN17B.11 Reset Connector CN18 Table B.11 Reset connector CN18Table B.13 ATX feature connector CN20 B.12 HDD LED Connector CN19B.13 ATX Feature Connector CN20 Table B.12 HDD LED connector CN19Table B.15 SM Bus connector CN29 B.14 ATX Soft Power Switch CN21B.15 SM Bus Connector CN29 Table B.14 ATX soft power switch CN21Table B.17 DMA channel assignments B.16 System I/O PortsB.17 DMA Channel Assignments Table B.16 System I/O portsTable B.19 1st MB memory map B.18 Interrupt AssignmentsB.19 1st MB Memory Map Table B.18 Interrupt assignmentsTable B.20 PCI bus map B.20 PCI Bus MapAppendixB PCA-6185 User’s Manual