Manuals / Aga Ranges / Household Appliance / Stove

Aga Ranges dc6 owner manual Fitting And Product Dimensions, Please Note When Fitting A Cooker Hood

Models: dc6

1 60

Download 60 pages 43.41 Kb

Page 6

Image 6

FITTING AND PRODUCT DIMENSIONS

Any side wall above the cooker on either side shall be not less than 60mm horizontally from the cooker (Fig. 1).

Surfaces over the top of the cooker must not be closer than 650mm.

A minimum clearance of 1000mm must be available at the front of the cooker to enable it to be serviced.

The vent slots in the back of the top plate must not be obstructed.

The cooker must stand on a firm and level surface we recommend that any soft material such as linoleum is removed.

PLEASE NOTE WHEN FITTING A COOKER HOOD

If a cooker hood is to be fitted, we only recommend the 6-4 Series CH900 cooker hood. It must be installed at a height of at least 800mm above the hotplate.

Fig. 1	DESN 512388 C

Page 6

Image 6

Aga Ranges dc6 owner manual Fitting And Product Dimensions, Please Note When Fitting A Cooker Hood

Contents

Cooking Guide Comprising Servicing, Installation & Users InstructionsAGA SIX-FOUR SERIES - DC6 FFD OWNERS MANUAL - NATURAL GAS For use in GB and IESECTION CONTENTSINSTALLATION SECTION PAGEInstallation Section INSTALLATION WARNING THIS APPLIANCE MUST BE EARTHEDTECHNICAL DATA ULTRA-RAPID RAPIDRAPID FITTING AND PRODUCT DIMENSIONS PLEASE NOTE WHEN FITTING A COOKER HOODELECTRICAL CONNECTION Fig. 2b DESNCONNECTING TO GAS COOKER STABILITY Fig. 3ADESN PRESSURE TESTING LEVELLING AND MOBILITY WHEELS INSTALLATION/LEVELLINGFITTING OF HOTPLATE CASTING AND PAN SUPPORTS HOTPLATE CASTINGSULTRA RAPID BURNER WOK BURNERFITTING BURNER CAP - RAPID AND SEMI-RAPID BURNERS ASSEMBLY OF RAPID AND SEMI-RAPID BURNERSBURNER CAP BURNER HEAD ELECTRODE BURNER CAP RETAINING LUGShotplate casting. See Fig. 8A & 8B SPLASHBACK TO ADJUST PAN SUPPORT LEVELHANDRAIL FITTING Users Guide GENERAL INFORMATION IMPORTANT NOTICE PLEASE READ THE ACCOMPANYING WARRANTYHEALTH & SAFETY APPLIANCEDeep Fat Frying DESN 512395 B Small Flame Symbol - Low Setting CONTROL PANELSymbol - Ignition Setting Large Flame Symbol - High Setting ClockwiseGAS HOTPLATE TO USE THE HOTPLATESOME SAFETY POINTS Fig. 13B TO FIT PAN SUPPORTSFig. 13A DESN 512995 ASETTING UP THE COOKER FOR USE SETTING THE TIME OF DAYGRIDDLE PLATE USING THE GRIDDLEz It MUST only be used on the right hand rapid burners THE SIMMERING OVEN SIMMERING OVENUSING THE SIMMERING OVEN SETTING STORAGE AND RE-HEATING OF FOODRagout of Beef in Ale Baked Potatoes Simmering OvenIDEAS FOR THE SIMMERING OVEN RecipesDauphinoise Potatoes Roast Fillet of Lamb Dauphinoise Potatoes Bread and Butter PuddingRecipes Roast fillet of Lamb Bread and Butter PuddingBraised Red Cabbage MealGammon and Apricot Pie St. Clements PuddingChilli Con Carne Meal RecipesChilli Con Carne Frangipane and Apple Pudding Frangipane and Apple PuddingSUGGESTED HEAT SETTING THE GRILLz THE GRILL COMPARTMENT DOOR MUST BE KEPT OPEN WHEN THE GRILL IS ON FOODTHE OVENS GeneralCondensation OVEN COOKING GUIDE Cooking HintsDeep Fat Frying FOOD SETTING Cz Thaw frozen joints before cooking them SHELF POSITIONSHELF POSITION SETTING CFOOD APPROXIMATE COOKING TIMEFOOD SETTING C45 mins - 1 hour using raw fruit 45 mins - 1 hour APPROXIMATE COOKING TIMEAPPROXIMATE COOKING TIME SETTING CFOOD Yeast MixturesTHE MINUTE TIMER SETTING THE MINUTE TIMERAn example of setting a programme using the cook time AUTOMATIC COOKING CONTROLSETTING THE AUTOMATIC COOKING PROGRAMME SETTING AN END TIME ONLY , AUTOMATICALLYz Do not use a steam cleaner to clean this cooker CLEANING & CARING FOR YOUR COOKERGeneral z Always switch OFF at the mains before cleaning THE COOKER CANNOT BE MOVED ONCE INSTALLEDHigh Temperature Protective Coating CLEANING & CARING FOR YOUR COOKERCLEANING METHOD COOKER PART AND FINISHDO NOT ANY ANY CLEANING MATERIAL CLEANING METHODHeat-Clean Enamel POWDERS, SOAP-FILLED PADS, WIREFig. 18A Oven Shelves - These shelves are designed to slide outRefit as follows Locate in guide as above Please Note Shelf slides out to stop positionFITTING BURNER CAP - RAPID AND SEMI-RAPID BURNER ASSEMBLY OF RAPID AND SEMI-RAPID BURNERBURNER CAP BURNER HEAD ELECTRODE BURNER CAP RETAINING LUGSDESN WOK BURNERULTRA RAPID BURNER DESNServicing Section SERVICING z Do not alter or modify the cookerz Only the spares specified by the manufacturer are to be fitted A. TO REMOVE HOTPLATE B. TO REMOVE SIDE PANELS C. TO REMOVE FACIA CASTINGSDESN 512407 B E. TO REMOVE TIMER D. TO REMOVE HANDRAIL SEE FIGF. TO REMOVE GAS TAPS/IGNITION SWITCHES I. TO REMOVE SPARK GENERATOR G. TO REMOVE GRILL REGULATORH. TO REMOVE OVEN THERMOSTATS DESN 513311 AJ. TO REMOVE ELECTRODES LHR, CF, CR, RHR, RHF BURNERS K. TO REMOVE ELECTRODE LH BURNER2. Proceed as ‘TO REMOVE THE HOTPLATE’ L. TO REMOVE THERMOCOUPLE LHF BURNER1. Isolate from electric supply 3. Undo the nut fixing the thermocouple in placeM. TO REMOVE THERMOCOUPLE LHR, RHR, RHF BURNERS N. TO REMOVE OVEN AND GRILL LINERS - SEE FIGO. TO REMOVE ELEMENTS RH OVENS P. TO REMOVE FAN OVEN ELEMENTQ. TO REMOVE OVEN FAN WIRING DIAGRAM - AGA DC6 Manufactured by Aga Station Road Ketley Telford Shropshire TF1 5AQ For further advice or information please contactyour local distributor/stockist England