Alliance Laundry Systems UW35B2, UW60B2 20

Programming

Permanent Diagnostic Test Cycle

		Control Test

	Warm fill to low water level	Display flashes “bFIL”/“LO” (WASH LED on), no agitation

		Outputs: Motor OFF, Drain closed, hot fill on, cold fill on

	Pause after reaching low water	Display shows “LO” (no flashing), LOW water level dot ON, no agitation (keypad WASH
	level	LED on); pauses until operator presses (∧) key

		Outputs: Motor OFF, Drain closed

	Drain (can advance to next step	Display shows “drAI”, no agitation (keypad WASH LED on)
	by pressing (∧) key here)
	by pressing (∧) key here)	Outputs: Motor OFF, Drain open
		Outputs: Motor OFF, Drain open

	Cold fill to medium level	Display flashes “CFIL”/“nEd” (keypad WASH LED on), no agitation.
		Outputs: Motor OFF, Drain closed, cold fill on

	Pause after reaching medium	Display shows “nEd” (no flashing), LOW and MEDIUM water level dots ON no agitation
	water level	(keypad WASH LED on); pauses until operator presses (∧) key

		Outputs: Motor OFF, Drain closed

	Hot fill to high level	Display flashes “HFIL”/“HI” (keypad WASH LED on), no agitation.

		Outputs: Motor OFF, Drain closed, hot fill on

	Pause after reaching high water	Display shows “HI” (no flashing), LOW, MEDIUM, and HIGH water level dots ON, no
	level	agitation (keypad WASH LED on); pauses until operator presses (∧) key

		Outputs: Motor OFF, Drain closed

	Heat to 110°F (45°C)	Display flashes “HEAt” and the temperature inside the machine while agitating in forward
	SKIPS THIS STEP if machine	and reverse; continues until temperature reaches 104°F (40°C), then advances to next step.
	does not have heat capability	(keypad WASH LED on)
	(“noHt” selected in Setup
	(“noHt” selected in Setup	Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 seconds
	Mode)
	Mode)	and repeats; Drain closed; Heat ON UNTIL 104°F (40°C) reached


	Extra supply / fill spare –	Display flashes ‘ESUP’ / ‘EFIL’ (keypad WASH LED on)
	5 seconds (depends on setup)
	5 seconds (depends on setup)	Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 seconds

		and repeats; Drain closed; ‘AF’ output ON.

	Supply 1: 5 seconds (Heat	Display shows ‘SUP1’ (keypad WASH LED on)
	signal also on (IF at least low
	signal also on (IF at least low	Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 seconds
	water level – verifies output
	water level – verifies output	and repeats; Drain closed; Supply 1 ON, HT ON, cold fill ON
	even if not heated model)	and repeats; Drain closed; Supply 1 ON, HT ON, cold fill ON
	even if not heated model)

	Supply 2: 5 seconds (Heat on	Display shows ‘SUP2’ (keypad ADD BLEACH LED on)
	also)
	also)	Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 seconds

		and repeats; Drain closed; Supply 2 ON, HT ON, cold fill ON

	Supply 3: 5 seconds (Heat on	Display shows ‘SUP3’ (keypad RINSE LED on)
	also)
	also)	Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 seconds

		and repeats; Drain closed; Supply 3 ON, HT ON, cold fill ON

	Supply 4: 5 seconds	Display shows ‘SUP4’ (keypad RINSE LED on)

		Outputs: Motor alternates forward 12 seconds, off 3, reverse 12 seconds, off 3 seconds
		and repeats; Drain closed; Supply 4 ON, cold fill ON

	Pause 5 seconds, then Forward	Display shows ‘For’
	wash speed – 60 seconds
	wash speed – 60 seconds	Outputs: Motor operates wash speed forward; drain closed
		Outputs: Motor operates wash speed forward; drain closed

		Table 2 (Continued)

F232168