Adjusting and Storing the Equalizer Curve
You can modify the Equalizer settings to create a response curve more appealing to your personal taste.
1 Press EQ to select the EQ mode.
2 Press and hold EQ for at least 2 seconds.
3 Press BAND/TEL. to select your desired frequency band.
BAND1 → BAND2 → BAND3 → BAND4 → BAND5 → BAND1
The initial setting of each BAND is as follows.
Frequency
BAND1: 50 Hz, BAND2: 250 Hz, BAND3: 1.0 kHz,
BAND4: 3.2 kHz, BAND5: 10 kHz
Level
Width (Q)
4 Press g or f to select your desired frequency.
Adjustable frequency bands:
20Hz to 20kHz (in 1/3 octave steps)
5 Turn the Rotary encoder to adjust the level.
6 Press SOURCE/POWER to select your desired band width (Q).
Adjustable band width: 1, 2, 3.
To store the adjusted curve
1)Press and hold any one of the preset buttons (1 through 6) into which you wish to store the adjusted curve for at least 2 seconds.
7 To set another channel, repeat steps 3 to 6.
8 After setting, press EQ to return to normal mode.
•The frequencies of adjacent bands cannot be adjusted within 4 steps.
•EQ mode is automatically cancelled if no buttons are pressed within 15 seconds.
•This function is inoperable when DEFEAT is set to ON (page 17).
•When you press DISP/B.OUT, you can switch the Level Indicator display to the EQ Adjustment display. For details, see “Changing the Audio Level Display Pattern” (page 7).
Recalling the Stored Equalizer Curve
1 Press EQ to select EQ mode.
2 Press and hold EQ for at least 2 seconds.
3 Press any one of the preset buttons (1 through
6)to activate your desired curve.
4 Press EQ to return to normal mode.
•EQ mode is automatically cancelled if no operation is performed within 15 seconds.
•This function is inoperable when DEFEAT is set to ON (page 17).
•If you do not adjust the factory settings of (FLAT/POPS/ROCK/ NEWS), the factory set display (FLAT/POPS/ROCK/NEWS) is shown preferentially.
About the Crossover (CDA-9815RB/CDA-9813R only)
Crossover:
This unit is equipped with an active crossover. The crossover limits the frequencies delivered to the outputs. Each channel is controlled independently. Thus, each speaker pair can be driven by the frequencies for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass filter) of each band, and also the slope (how fast the filter rolls off the highs or lows).
Adjustments should be made according to the reproduction characteristics of the speakers. Depending on the speakers, a passive network may not be necessary. If you are unsure about this point, please consult your authorized Alpine dealer.
2 way mode
| Slope |
| ||||
| (1/3 octave steps) |
| ||||
|
|
| Level | |||
|
|
|
|
| ||
|
|
|
|
|
| |
| HPF | LPF | HPF | LPF |
| |
|
|
|
|
|
| |
|
|
|
| FLAT, −6, |
| |
Low range | 20 Hz - | −12, −18, | 0 to | |||
speaker | 200 Hz | −24 dB/ | −12 dB | |||
|
| |||||
|
|
|
| oct |
| |
|
|
|
|
|
| |
Rear high |
|
| FLAT, −6, |
|
| |
20 Hz - |
| −12, −18, |
| 0 to | ||
range | ||||||
200 Hz | −24 dB/ | −12 dB | ||||
speaker |
|
| ||||
|
| oct |
|
| ||
|
|
|
|
| ||
|
|
|
|
|
| |
Front high |
|
| FLAT, −6, |
|
| |
20 Hz - |
| −12, −18, |
| 0 to | ||
range | ||||||
200 Hz | −24 dB/ | −12 dB | ||||
speaker |
|
| ||||
|
| oct |
|
| ||
|
|
|
|
| ||
|
|
|
|
|
| |
Low range | High range |
(Different from actual display)
