Memorizing the Service

1 Select the service that you want to memorize.

2 Press any one of the Preset buttons (1 through

6)for at least 2 seconds while the “FUNC” indicator (only underlined portion of the “FUNC” indicator for CDA-9811R) goes out. The selected service is memorized.

3 To memorize more, repeat the above steps 1 and 2.

You can memorize up to 18 stations (6 stations for each band; DAB1, DAB2, DAB3).

If you select a preset button that has already memorized a service, the new selection takes it over.

When you are not receiving DAB, the service is not memorized. (Memorize the service when the DAB reception is good)

Receiving the Memorized Service

1 Press BAND/TEL. to select your desired band.

2 Press one of the Preset buttons (1 through 6).

The selected service is received.

By selecting the mode in the “Changing the Display Mode” (page 31), the display shows the status of the broadcasting stations that have been received as follows:

Channel No. Display: the channel numbers of received stations are displayed.

Ensemble Label Display: the Ensemble Label of received station is displayed.

Service Label Display: the Ensemble Label is displayed for 2 seconds and then the Service Label is displayed after receiving the broadcasting station.

Component Label Display: the Ensemble Label is displayed for 2 seconds, then the Service Label is displayed for 2 seconds, and then the display is changed to the Component Label after receiving the broadcasting station.

Dynamic Label Display: the Ensemble Label is displayed for 2 seconds, then the Service Label is displayed for 2 seconds, and then the display is changed to the Dynamic Label after receiving the broadcasting station.

Frequency Display*1 : the frequency of received stations are displayed.

To switch the frequency display on the CDA-9813R/CDA-9812RX/ CDA-9811R, press TITLE. For details, see “Changing the Display Mode” (page 31).

When you receive the Secondary Service Component, you memorize the service, but when you call out this memorized service, the Primary Service Component will be called out.

*1 CDA-9813R/CDA-9812RX/CDA-9811R only

Memorizing the Ensemble Automatically

1 Press BAND/TEL. to select the band that you want to receive.

2 Press and hold TUNE/A.ME for at least 2 seconds.

The ensemble is searched for, and six ensembles are automatically received and memorized with the preset buttons (1 through 6).

When memorization has completed, the Ensemble that was memorized last is received.

By selecting the mode in the “Changing the Display Mode” (page 31), the display shows the status of the broadcasting stations that have been received as follows:

Channel No. Display: the channel numbers of received stations are displayed.

Ensemble Label Display: the Ensemble Label of received station is displayed.

Service Label Display: the Ensemble Label is displayed for 2 seconds and then the Service Label is displayed after receiving the broadcasting station.

Component Label Display: the Ensemble Label is displayed for 2 seconds, then the Service Label is displayed for 2 seconds, and then the display is changed to the Component Label after receiving the broadcasting station.

Dynamic Label Display: the Ensemble Label is displayed for 2 seconds, then the Service Label is displayed for 2 seconds, and then the display is changed to the Dynamic Label after receiving the broadcasting station.

Frequency Display*2 : the frequency of received stations are displayed.

To switch the frequency display on the CDA-9813R/CDA-9812RX/ CDA-9811R, press TITLE. For details, see “Changing the Display Mode” (page 31).

If no ensemble is received, the one that has been received before you perform this automatic memorization is received.

*2 CDA-9813R/CDA-9812RX/CDA-9811R only

PTY (Programme Type) Tuning

1 Press F/SETUP so that the “FUNC” indicator lights up. (Only the underlined portion of the “FUNC” indicator for CDA-9811R.)

2 Press 3/PTY to go to the PTY Select mode.

3 Press g or f to select your desired programme type.

4 After selecting a programme type, and when the “FUNC” indicator lights up (only the underlined portion of the “FUNC” indicator for CDA-9811R), press 3/PTY to go to the PTY Search mode.

To cancel the PTY Search mode during the PTY search, press the PTY button.

5 When the station is received, the received programme type is displayed for 5 seconds. If no station is found, “NO PTY” is displayed for 5 seconds.

30-EN

• Above functions can be performed only for services within an

Ensemble.

 

Page 32
Image 32
Alpine CDA-9813R Memorizing the Service, Receiving the Memorized Service, Memorizing the Ensemble Automatically, 30-EN