Alpine CDA-9811R, CDA-9812RR, CDA-9815RB, CDA-9813R Bass Focus, Example setting for steps 2, 22-EN

Bass Focus

The time difference between the front-rear/left-right speakers, can be adjusted at the same time. With an initial delay of 0.1 ms for each of the 0 to 99 steps, audible time correction can be done.

1 Press T.CORR/X-OVER to select the Bass Focus mode.

Bass Focus mode → Time correction mode → normal mode

→Bass Focus mode

(2)Press BAND/TEL. to select the left (front and rear) speakers. Then turn the Rotary encoder to select 1.5 ms (Delay no. 15 in the table). The time difference is 3.0 ms*2 for the front left speaker, and 1.5ms for the left rear speaker, creating the impression of an equal listening between the front left speaker and the other speakers.

2 Press BAND/TEL. to select the speakers to be adjusted (see below).

→	FL	FR	→	FL	FR
	RL	RR		RL	RR
	Front (left-right)			Left (front-rear)
	speakers			speakers

3.0ms

1.5ms 1.5ms

1.5ms

1.5ms

*1

FL	FR	←	FL	FR	←
RL	RR		RL	RR
Rear (left-right)			Right (front-rear)
speakers			speakers

3 Turn the Rotary encoder to adjust the delay (see Time Difference Table).

4 To set another channel (speakers), repeat steps 2 and 3.

5 After setting, press and hold T.CORR/X-OVER for at least 2 seconds to return to normal mode.

•Any manual time correction adjustments will also affect corrections made in Bass Focus.

•Bass Focus mode is automatically cancelled if no operation is performed within 15 seconds.

Example setting for steps 2 and 3

(1)Press BAND/TEL. to select the front (left and right) speakers. Then turn the Rotary encoder to select 1.5 ms (Delay no. 15 in the table). The time difference is 1.5 ms for both front (left and right speakers.

*1 Subwoofer speaker. CDA-9812RX/CDA-9811R only

Delay (turn the rotary encoder) the audio signal to the front (left and right) speakers to make the apparent position of the subwoofer to be at the front. In doing this, the apparent position between the front (left and right) speakers and subwoofer will appear equal to the driver. After performing the above, you can change the positions of the left and right speakers by delaying the time .

*2 Because the time difference was already set to 1.5ms for the front left speaker to begin with, the additional correction of 1.5ms makes the total time difference of the front left speaker 3.0ms.

Time Difference Table

Delay	Time	Delay	Time	Delay	Time
	Difference		Difference		Difference
Number	(ms)	Number	(ms)	Number	(ms)
0	0.0	14	1.4	28	2.8
1	0.1	15	1.5	29	2.9
2	0.2	16	1.6	30	3.0
3	0.3	17	1.7	31	3.1
4	0.4	18	1.8	32	3.2
5	0.5	19	1.9	33	3.3
6	0.6	20	2.0	34	3.4
7	0.7	21	2.1	35	3.5
8	0.8	22	2.2	36	3.6
9	0.9	23	2.3	37	3.7
10	1.0	24	2.4	38	3.8
11	1.1	25	2.5	39	3.9
12	1.2	26	2.6	40 - 98	4.0 - 9.8
13	1.3	27	2.7	99	9.9

1.5ms

1.5ms

*1

22-EN