Alpine MRP-T130 specifications CONNECTIONS - Fig, MRP-F320, MRP-F200

CONNECTIONS (Fig. 3 – Fig. 13)

MRP-F320

+

–

CH-2 +

–

CH-1

+

30A

BATTERY REMOTE

GND

SPEAKER

OUTPUT

SUB W

30

–

– CH-4 +

–

CH-3 +

POWER SUPPLY

FUSE

–

BRIDGED

+

(Rear side/Arrière/Parte trasera)

6

7

22

8

21

9

20

10

19

18

17

14

12

16

15

13

NOM

NOM

NOM

100

CH-1

CH-3

CH-1 2 3 4

0.5V

0.5V

0.5V

75

140

+

55

170 (L)

–

MIN

MAX

OFF HP

MIN

MAX

OFF

HP MIN

MAX

OFF ON

50

200

INPUT

GAIN

(80Hz)

GAIN

(80Hz)

GAIN

BASS BOOST

LP FILTER

FILTER

FILTER

CHANNEL-1/2

CHANNEL-3/4

Sub woofer

(R)

SPEAKER

LEVEL INPUT

CH-2

CH-4

(Front side/Avant/Parte delantera)

MRP-F200

–

CH-2

+

–

CH-1

+

25A

BATTERY REMOTE

GND

SPEAKER

25

OUTPUT

–

CH-4

+

–

CH-3

+

POWER SUPPLY

FUSE

–

BRIDGED

+

(Rear side/Arrière/Parte trasera)

6

7

22

8

21

9

20

10

19

18

17

14

11

12

16

15

13

NOM

NOM

CH-1+3

CH-1

CH-3

CH-1 2 3

4

0.5V

0.5V

+

(L)

–

MIN

MAX

OFF HP LP

MIN

MAX OFF

ON

OFF HP LP

PRE

INPUT

GAIN

(80Hz)

GAIN

BASS BOOST

(80Hz)

FILTER

FILTER

OUT

CHANNEL-1/2

CHANNEL-3/4

(R)

SPEAKER

LEVEL INPUT

CH-2+4

CH-2

CH-4

(Front side/Avant/Parte delantera)

MRP-T130

–

BRIDGED

+

BATTERY REMOTE

GND

–

CH-2

+

–

CH-1

+

20A

SPEAKER

20

OUTPUT

POWER SUPPLY

FUSE

(Rear side/Arrière/Parte trasera)

6

7

8

18

9

17

10

16

15

14

12

13

NOM

INPUT

CH-1 CH-2

0.5V

+

–

OFF HP LP

OFF

ON

MIN

MAX

(80Hz)

BASS BOOST

GAIN

(L)

(R)

FILTER

SPEAKER

Fig. 3

LEVEL INPUT

(Front side/Avant/Parte delantera)

Before making connections, be sure to turn the power off to all audio components. Connect the yellow battery lead from the amp directly to the positive (+) terminal of the vehicle's battery. Do not connect this lead to the fuse block.

To prevent external noise from entering the audio system.

•Locate the unit and route the leads at least 10 cm away from the car harness.

•Keep the battery power leads as far away from other leads as possible.

•Connect the ground lead securely to a bare metal spot (remove the coating if necessary) of the car chassis.

•If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various Alpine noise suppressors, contact them for further information.

•Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

6Speaker Output Terminal

The MRP-F320/MRP-F200/MRP-T130 has two sets of speaker outputs. Be sure to observe correct speaker output connections and phasing. In the stereo mode, connect the right speaker outputs to the right speaker and the left to left. Connect the positive output to the positive speaker terminal and the negative to negative.

In the bridged mode, connect the left positive to the positive terminal on the speaker and the right negative to the negative terminal of the speaker. Do not use the speaker (–) terminals as a common lead between the left and right channels. Do not connect this lead to the vehicle's chassis.

NOTES:

1.Do not connect speaker leads together or to chassis ground.

2.In case of bridge connection, use Y-adaptor (sold separately). (Refer to the "Bridge Connections" below.)

7Insulation Tube

Use for POWER SUPPLY (BATTERY/REMOTE/ GND) and SPEAKER OUTPUT terminals.

8Ground Lead (Black) (Sold Separately) Connect this lead securely to a clean, bare metal spot on the vehicle's chassis. Verify this point to be a true ground by checking for continuity between that point and the negative

(–) terminal of the vehicle's battery. Ground all your audio components to the same point on the chassis to prevent ground loops.

9Remote Turn-On Lead (Blue/White) (Sold Separately)

Connect this lead to the remote turn-on or power antenna (positive trigger, (+) 12V only) lead of your head unit.

10Battery Lead (Yellow) (Sold Separately) Be sure to add a ★30 amp fuse as close as possible to the battery's positive (+) terminal. This fuse will protect your vehicle's electrical system in case of a short circuit. If you need to extend this lead, the wire gauge should be 8 AWG or larger.

★MRP-F320 ... 30 amp fuse MRP-F200 ... 25 amp fuse MRP-T130 ... 20 amp fuse

11Pre-Out Jacks (MRP-F200 only)

These jacks provide a Front + Rear summed output (Non-fading ). This is an ideal output for driving a separate subwoofer amp. This output is full-range, and is not affected by the crossover.

12RCA Input Jacks

Connect these jacks to the line out leads on your head unit using RCA extension cables (sold separately). Be sure to observe correct channel connections; Left to Left and Right to Right. (Front to Front and Rear to Rear (except for MRP-T130))

13Speaker Level Input Connector

These leads are input leads for use with head units not equipped with preamp outputs. When not using the RCA Line Input connectors, you should connect these wires to the speaker output leads of your head unit. The MRP-F320/ MRP-F200/MRP-T130 accepts input from high power or standard power head units.

14Speaker Input Leads

These leads are input leads for use with head units not equipped with preamp outputs. Connect these wires to the speaker output leads of your head unit. The MRP-F320/MRP-F200/ MRP-T130 accepts input from high power or standard power head units.

15Front Left Speaker (White (+))

16Front Left Speaker (White/Black (–))

17Front Right Speaker (Gray (+))

18Front Right Speaker (Gray/Black (–))

19Rear Left Speaker (Green (+)) (except for MRP-T130)

20Rear Left Speaker (Green/Black (–)) (except for MRP-T130)

21Rear Right Speaker (Violet (+)) (except for MRP-T130)

22Rear Right Speaker (Violet/Black (–)) (except for MRP-T130)