Alvarion BU-DS.11, RB-DS.11 Trap Monitor Tab

The DS.11 Configuration Utility

3-27

♦ Set Compatibility Mode: Click to set the following parameters, which are

unique to DS.11 version 4.0, to values that will ensure interoperability with

DS.11 units running previous versions as well as with other IEEE 802.11

compliant devices:

 Basic rate=2Mbps

 Short preamble = Disable (BU)

 Scrambling: Disable

NOTE:

To ensure compatibility, verify that a 128-bit WEP Key is not used.

♦ Set High Performance Mode: The units can be configured to deliver high

performance (high throughput) if the RSSI of all links is –80 dBm or better,

provide that all units run SW version 4.0. Upon clicking this button, the

following parameters will be configured to support high performance:

 Basic rate=11Mbps

 Short Preamble = Enable (only in BU)

Trap Monitor Tab

The Trap Monitor tab enables you to view messages received from the selected unit.

Figure 3-17: Trap Monitor Tab

When an event occurs, a trap is sent to the defined host address (the setting is

made in the SNMP Parameters tab described on page 3-7). This window displays

the recorded traps.

Click Clear List to clear the display area.

Contents

Main Page iii Trade Names Statement of Conditions Warranties; Disclaimers Exclusive Warranty iv Disclaimer v Limitation of Liability Electronic Emission Notices FCC Radio Frequency Interference Statement vi FCC Radiation Exposure Statement Antenna Installation vii Important Notice viii Contacting Alvarion Technical Support www.alvarion.com/support.htm User Manual Table of Contents Introduction 1-1 Installation 2-1 The DS.11 Configuration Utility 3-1 Configuration Guidelines 4-1 System Troubleshooting 5-1 Technical Specifications 6-1 DS.11 FAQ A-1 Preparing the Indoor to Outdoor Cable 1 Radio Signal Propagation 1 Table of Figures Table of Tables 1-1 Chapter 1 1-2 Scope of the Manual 1-3 System Description Functional Description BU-DS.11 Wireless Base Unit 1-4 RB-DS.11 Wireless Bridge BreezeNET DS.11 Compatibility and Standards 2-1 Chapter 2 2-2 Packing List Additional Installation Requirements Installation Overview 2-4 2-5 Outdoor Installation Considerations Collocating DS.11 Outdoor Units Site Selection Factors Path of Clearest Propagation Physical Obstacles Rooftop Installation Antennas for Outdoor Applications The Point-to-Point Point-to-Multipoint Antenna Seal Cell Size/Link Distance Using Outdoor Range Tables Available Antennas Precautions Compliance with Radio Regulations 2-9 Installing the Outdoor Unit 2-10 2-11 Connecting the Ground and Antenna Cables 1. 2. Connecting the Indoor-to-Outdoor Cable Page 2-13 Installing the Indoor Unit 1. 2. 3. 4. Configuring Parameters Antenna Alignment 1. 2. 2-15 Verifying Correct Operation Verifying Correct Operation of the Indoor Unit Table 2-2: Indoor Unit LEDs Verifying Correct Operation of the Outdoor Unit 2-16 What to do if the Self Test Fails 3-1 Chapter 3 3-2 Installing and Accessing the Configuration Utility 1. 2. 3. 4. Configuration Utility Modes Unit Configuration Mode Control Window Tabs Section 3-4 Control Window Selecting Units Setting the SNMP Community String Assigning and Editing IP Addresses Manually (based on MAC addresses) 1. Application Control Buttons Configuration Utility Tabs Station Status Tab 3-6 Networking Parameters Tab Networking Parameters-General Tab IP Parameters 3-7 DHCP VLAN Support 3-8 3-9 Networking Parameters-CPE Table Tab (BU only) 3-10 3-11 SNMP Parameters Tab 3-12 Counters Tab 3-13 3-14 WLAN Parameters Tab 3-15 3-16 Table 3-1: Regulatory Domains Specifications Table 3-2: Frequency List 3-17 Station Control Tab 3-18 Security Tab Encryption Tab 3-19 3-20 ACL Table Tab (BU only) 3-21 Advanced Tab 3-22 3-23 General Parameters Tab 3-24 3-25 3-26 Auto-Config Tab 3-27 Trap Monitor Tab 3-28 Firmware Upgrade Mode 1. 2. 3. Advanced TFTP Settings 3-30 Multiple Unit Configuration Mode 3-31 Resetting the SNMP Community Strings Reloading Factory Default Settings 1. 2. Page 4-1 Chapter 4 4-2 Configuring Critical Parameters One-Click Configuration Short Preamble CW Minimum 4-3 RTS Threshold Basic Rate Range Page 5-1 Chapter 5 5-2 Troubleshooting Guide 6-1 Chapter 6 Supported Standards Configuration and Management 6-2 Radio Range Security Page Page A-1 Appendix A A-2 General A-3 A-4 Collocation and Interference A-5 Firmware A-6 Configuration A-7 Accessories A-8 Management B-1 Appendix B 1. 2. Page C-1 Appendix C RF Terms and Definitions dB RF Power Level C-2 Attenuation P For example: If, due to attenuation, half the power is lost (P Path Loss Free Space Loss Antenna Characteristics C-4 Directional Antenna Antenna Beamwidth System Characteristics Receiver Sensitivity EIRP (Effective Isotropic Radiated Power) Si = P C-5 Link Parameters Link Budget Calculation Signal Fading C-6 The Line of Sight Concept Clear Line of Sight Fresnel Zone R = :