I. Safety and Unit Location

WARNING

To prevent personal injury or death due to improper installation, adjustment, alteration, service, or, maintenance refer to this manual or for additional assistance or information consult a qualified installer, service agency or the gas supplier.

WARNING

This product contains or produces a chemical or chemicals which may cause serious illness or death and which are known to the State of California to cause cancer, birth defects or other reproductive harm.

WARNING

To prevent possible death, personal injury or equipment damage due to fire, the following points must be observed when installing the unit.

WARNING

To prevent possible death, personal injury or property damage due to electrical shock, the furnace must be located to protect the electrical components from water.

NOTE: This unit must not be used as a “construction heater” during the finishing phases of construction on a new structure. This type of use may result in premature failure of the unit due to extremely low return air tempera- tures and exposure to corrosive or very dirty atmospheres.

WARNING

To prevent possible death, personal injury or property damage, do not install this unit in a mobile home, trailer or recreational vehicle.

ADDITIONAL SAFETY CONSIDERATIONS

This furnace is approved for Category I Venting only.

When the furnace is heating, the temperature of the return air entering the furnace must be between 55°F and 100°F.

Do not install the furnace where the combustion air is exposed to the following substances: permanent wave solutions, chlorinated waxes or cleaners, chlorine based swimming pool chemicals, water softening chemicals, deicing salts or chemicals, carbon tetra- chloride, halogen type refrigerants, cleaning solutions (such as perchloroethylene), printing inks, paint re- movers, varnishes, hydrochloric acid, cements and glues, antistatic fabric softeners for clothes dryers,

and masonry acid washing materials. If the furnace is installed near an area which will be frequently con- taminated by these substances, the furnace should be sealed from this area so that little contaminated air can reach the furnace. The furnace must still have an adequate supply of combustion air, either from a nearby uncontaminated room or from outdoors. For details, see “AIR REQUIREMENTS” Section III.

Provisions must be made for venting combustion products outdoors through a proper venting system. The length of flue pipe could be a limiting factor in locating the furnace.

When installed horizontally, the furnace must be in- stalled with the access doors vertical so that the burners fire horizontally into the heat exchanger. The unit cannot be installed with the access doors on top or bottom. (See Specification Sheet)

Allow clearances from the enclosure as shown on Specification Sheet for fire protection, proper opera- tion, and service access. These clearances must be permanently maintained. The combustion and venti- lating air openings in the front and top panels of the furnace must never be obstructed.

This furnace shall not be connected to a chimney flue serving a separate appliance designed to burn solid fuel.

When the furnace is used in connection with a cooling unit, the furnace must be upstream of, or in parallel with, the cooling unit. For details see Section VIlI.

On Counterflow Installations, the air conditioning coil must be downstream from the heat exchanger of the furnace.

Counterflow Installation over a noncombustible floor. Before setting the furnace over the plenum opening, insure the surface around the opening is smooth and level. A tight seal should be made between the furnace base and floor by using a silicone rubber caulking compound or cement grout.

Counterflow Installation over a combustible floor. If installation over a combustible floor becomes neces- sary, use an accessory subbase as shown on the Specification Sheet. Follow the instructions with the subbase for proper installation. Do not install the furnace directly on carpeting, tile, or other combustible material other than wood flooring. (Note: The subbase will not be required if an air conditioning coil is installed between the supply air opening on the furnace and the floor.)

The furnace must be level. If the furnace is to be set on a floor that may become wet or damp at times, the furnace should be supported above the floor on a concrete base sized approximately 1-1/2" larger than the base of the furnace.

ADDITIONAL LOCATION CONSIDERATIONS

The furnace should be as centralized as is practical with respect to the air distribution system.

Do not install the furnace directly on carpeting, tile, or combustible material other than wood flooring.

When suspending the furnace from rafters or joists, use 3/8" threaded rod and 2” x 2” x 3/8” angle as shown on the Specification Sheet. The length of the rod will depend on the application and clearance necessary.

3

Page 3
Image 3
Amana VR8205 installation instructions Safety and Unit Location, Additional Safety Considerations

VR8205 specifications

The Amana VR8205 is a robust and innovative gas valve designed for use in a variety of heating applications, particularly in residential and commercial HVAC systems. This versatile valve offers a combination of advanced technologies and user-friendly features, making it a popular choice among HVAC professionals and system installers alike.

One of the key features of the Amana VR8205 is its two-stage operation, allowing for precise control of gas flow. The dual-stage design enables the valve to modulate the gas supply based on the heating demand, which enhances system efficiency and promotes better temperature regulation. This feature not only contributes to energy savings but also helps maintain a comfortable indoor environment.

Additionally, the VR8205 is equipped with a strong, durable body construction that ensures reliability and longevity. Designed to withstand harsh operating conditions, the valveā€™s materials are resistant to corrosion and wear, making it suitable for various applications. The robust design of the Amana VR8205 minimizes the likelihood of leaks or failures, providing peace of mind to both installers and end-users.

The valve operates on low voltage, typically requiring 24 volts, which makes it energy-efficient and compatible with most modern thermostatic control systems. This low-voltage operation also simplifies installation, as it reduces the complexity and requirements for the electrical setup.

Another noteworthy characteristic of the Amana VR8205 is its integrated safety features. It includes a combination of automatic and manual shut-off mechanisms, providing an added layer of safety in case of malfunctions. This ensures that the gas supply can be quickly halted in emergency situations, protecting both people and property.

Moreover, the Amana VR8205 is designed for easy maintenance, featuring simple access points for servicing and troubleshooting. This ease of maintenance is crucial for HVAC professionals, as it allows for quick adjustments and repairs, ultimately reducing downtime.

Lastly, the Amana VR8205 has a reputation for adaptability, being compatible with various heating appliances, including furnaces, boilers, and water heaters. Its versatility makes it an excellent solution for a wide range of heating applications, ensuring optimal performance across different systems.

In summary, the Amana VR8205 gas valve is characterized by its two-stage operation, durable construction, low-voltage functionality, integrated safety mechanisms, and ease of maintenance. These features combine to offer a reliable, efficient, and flexible solution for modern heating needs.