Flight Moon™

Set Up

 

 

Flight Moon™

Fuse & Lamp Replacement

 

 

XLR Male Socket

XLR Female Socket

1 Ground

2 Cold

2 Cold

1 Ground

 

 

3 Hot

 

3 Hot

Figure 3

XLR Pin Configuration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

Caution: Always replace with the exact same type lamp and fuse, unless otherwise specified by an authorized American DJ® technician. Replace with anything other than the specified part can damage your unit and will void your manufactures warranty.

Warning: If, after replacing the lamp or fuse either one continues to blow, STOP using the unit. Contact customer support for further instructions, you may have to return the unit for servicing. Continuing

Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con- nected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

 

Termination reduces signal errors and

 

1

avoids signal transmission problems

 

3

and interference. It is always advisable

 

2

to connect a DMX terminal, (Resistance

 

 

120 Ohm 1/4 W) between PIN 2 (DMX-)

Figure 4

 

and PIN 3 (DMX +) of the last fixture.

5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor

3-Pin XLR Female (Out)

5-Pin XLR Male (In)

 

 

 

Ground/Shield

Pin 1

Pin 1

 

 

 

Data Compliment (- signal)

Pin 2

Pin 2

 

 

 

Data True (+ signal)

Pin 3

Pin 3

 

 

 

 

Not Used

 

Do Not Use

 

 

 

 

Not Used

 

Do Not Use

 

 

 

 

to use the unit may cause serious damage.

Fuse Replacement: Disconnect the unit’s main power supply. Insert a standard flat head screw driver in to the fuse holder housing. Turn the screwdriver in counter-clockwise direction to remove the fuse holder. Remove the fuse holder to expose the fuse. Remove the old fuse and discard it. Replace the fuse with the same type. Insert the fuse holder back into it’s housing and turn it in clockwise direction to lock the holder in place.

Lamp Replacement: Caution! Never attempt to change the lamp while the fixture is plugged in. Always disconnect the main power and allow the unit ample time to cool before attempting to replace the lamp. Lamp replacement has been made simple by incorporating the use of a flip-up front cover that is retained by thumb screws.

1.Be sure to follow the proper handling procedures that deal with halogen lamps.

2.Remove the thumb screw on the top/rear of the unit that holds the lamp socket assembly cover in place.

3.After removing the thumb screw, slide out the cove from the rear of the unit to expose the lamp socket assembly.

4.Carefully remove the old lamp and discard it in the trash.

5.Replace the lamp with an exact match and reassemble in reverse order.

Halogen Lamp Warning: This fixture is fitted with halogen lamps which are highly susceptible to damage if improperly handled. Never touch the lamps with your bare fingers as the oil from your hands will shorten lamp life. Also, never move the fixture until the lamps have had ample time to cool. Remember, lamps are not covered under warranty conditions.

©American DJ® - www.americandj.com - Flight Moon™ Instruction Manual Page 11

©American DJ® - www.americandj.com - Flight Moon™ Instruction Manual Page 12

Page 6
Image 6
American DJ Flight-Moon instruction manual Flight Moon Set Up Fuse & Lamp Replacement, Pin XLR to 5-Pin XLR Conversion

Flight-Moon specifications

American DJ Flight-Moon is an innovative lighting fixture that has taken the world of mobile DJs, event planners, and entertainers by storm. Designed with versatility and user-friendliness in mind, this LED moonflower effect projector creates captivating lighting displays that enhance any performance or event.

One of the standout features of the Flight-Moon is its 10-watt RGBW LED, which produces vibrant and dynamic colors that can be projected onto walls, ceilings, or dance floors. The combination of red, green, blue, and white LEDs allows for a broad spectrum of colors, enabling users to customize their lighting effects according to the atmosphere of the event.

The device is equipped with a wide beam angle and a multitude of intricate patterns that rotate and move, providing an eye-catching visual impact that can energize any crowd. This dynamic movement can be controlled via sound activation, meaning that the light will pulse and dance in sync with the music, creating an immersive experience for attendees.

In addition to sound activation, the Flight-Moon offers multiple operational modes. Users can take advantage of its built-in automatic programs for effortless setup, or use DMX control for more advanced programming capabilities. This flexibility allows for both novice and experienced users to achieve their desired effects, whether that be for a small party or a large concert setting.

The Flight-Moon also boasts a compact and lightweight design, making it easy to transport, set up, and remove. Its rugged construction ensures durability, allowing it to withstand the rigors of frequent use in various environments. This portability is especially beneficial for mobile DJs and event suppliers who often work on the go.

Furthermore, this fixture includes a low power consumption feature, which allows for extended use without the worry of overheating or excessive energy bills. The LED technology not only saves energy but also requires less maintenance compared to traditional lighting solutions.

Overall, American DJ's Flight-Moon is a remarkable lighting fixture that combines impressive technology, versatility, and user-friendliness. Its ability to create stunning visual effects and adapt to different environments makes it a top choice for DJs, party planners, and anyone looking to elevate their lighting experience.