American Dryer Corp AD-120ES II B. COMPONENT IDENTIFICATION

B. COMPONENT IDENTIFICATION

1. Dryer Front View

Illus. No. Description

1Microprocessor Control/Keyboard (touch pad) Panel Assembly (controls)

2Control (top access) Door Assembly

3Main Door Assembly

4Lint Door Assembly

5Lint Drawer

6Wire Diagram (located behind control door)

7Top Console (module) Assembly

Contents

Main AD-120ES II (Extended Side Panels) Installation Manual Retain This Manual In A Safe Place For Future Reference AD-120ES II Important Page Page Table of Contents Page SECTION I IMPORTANT INFORMATION IMPORTANT: The dryer must be transported and handled in an upright position at ALL times. A. RECEIVING AND HANDLING B. SAFETY PRECAUTIONS Page SECTION II SPECIFICATIONS/COMPONENT IDENTIFICATION Steam A. SPECIFICATIONS Gas Specifications ADG-120ES II ADE-120ES II ADS-120ES II B. COMPONENT IDENTIFICATION Page SECTION III INSTALLATION PROCEDURES A. LOCATION REQUIREMENTS IMPORTANT: The dryer must be installed on noncombustible floors only. IMPORTANT: Dryer should be located where a minimum amount of exhaust duct will be necessary. B. UNPACKING/SETTING UP IMPORTANT: The dryer must be transported and handled in an upright position at ALL times. WARNING THIS EXHAUST DUCT TRANSITION PIECE MUST BE INSTALLED FIRST! C. DRYER ENCLOSURE REQUIREMENTS D. FRESH AIR SUPPLY REQUIREMENTS E. EXHAUST REQUIREMENTS Page Page Page Page Page F. ELECTRICAL INFORMATION ADG-120ES II Reversing, 3 (GAS) ADS-120ES II Reversing, 3 (STEAM) ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER) ADE-120 II (72 Kw Electric) Reversing, 3 ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER) SERVICE VOLTAGE PHASE WIRE OVEN SIZE (Kw) SERVICE ADE-120 II (80 Kw Electric) Reversing, 3 ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER) SERVICE VOLTAGE PHASE WIRE OVEN SIZE (Kw) SERVICE NOTE: A CIRCUIT SERVICING EACH DRYER MUST BE PROVIDED. Page G. GAS INFORMATION TYPE OF GASLiquid Propane TYPE OF GAS NATURAL LIQUID PROPANE Page Page H. STEAM INFORMATION Operating Steam Pressure Page COMPRESSED AIR SUPPLYAIR PRESSUR E Normal 80 PSI 5.52 bars Minimum Supply 70 PSI 4.83 bars Maximum Supply 90 PSI 6.21 bars Page I. PREPARATION FOR OPERATION J. PREOPERATIONAL TESTS Page K. SHUT DOWN INSTRUCTIONS L. OPERATING INSTRUCTIONS SECTION IV SERVICE/PARTS INFORMATION A. SERVICE B. PARTS SECTION V WARRANTY INFORMATION A. RETURNING WARRANTY CARDS B. WARRANTY C. RETURNING WARRANTY PARTS Page SECTION VI ROUTINE MAINTENANCE A. CLEANING SUGGESTED CLEANING SCHEDULE Page B. ADJUSTMENTS C. LUBRICATION SECTION VII TROUBLESHOOTING MICROPROCESSOR CONTROLLER (COMPUTER) MODELS Page Page Page P. No heat (for GAS MODEL ONLY)...ignitor sparks, burner goes on and off right away... Q. No heat (for STEAM MODELS ONLY)... R. No heat (for ELECTRIC MODELS ONLY)... S. Dryer operates but is taking too long to dry... T. Condensation on main door glass... U. Dryer is making scraping noise at basket (tumbler) area... V. Excessive noise and/or vibration... TIMER MODELS Page ELECTRIC MODELS STEAM MODELS G. Heat unit is not operating for ONLY one (1) temperature selection... H. Dryer operates but is taking too long to dry load... I. Dryer is cycling on hi-limit thermostat (for GAS AND ELECTRIC MODELS ONLY)... J. Condensation on main door glass... K. Dryer is making scraping noise at basket (tumbler) area... L. Excessive noise and/or vibration... Page Page SECTION IX REVERSING TIMER SPIN/DWELL ADJUSTMENTS TIMING LEGEND SECTION X Page Page SECTION XI BURNER AND BASKET (TUMBLER)/LINT CHAMBER I M P O R T A N T FOR TIMER OR PHASE 5 WITHOUT HEAT FAULT (GAS MODELS ONLY) IMPORTANT I M P O R T A N T FOR TIMER OR PHASE 5 WITHOUT HEAT FAULT (ELECTRIC OR STEAM MODELS ONLY) IMPORTANT