6
BOLT CAP
WASHER
NUT
BOLTS
CLOSET BOLT
INSTALL TOILET
a.Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
! CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b.Install caps on washers. (If necessary, cut bolt height to size before installing caps.)
c.Smooth off the bead of sealant around base. Remove excess sealant.
CLOSET FLANGE
7INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
8a | Before continuing, determine the type of water supply connection you have from |
| the chart below and use the appropriate assembly parts required to properly |
|
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL/COPPER | METAL FLANGED | METAL SPIRAL | VINYL/BRAIDED |
FLARED TUBING | TUBING | TUBING | CONNECTOR |
LOCK NUT | LOCK NUT | LOCK NUT | LOCK NUT |
CONE | EXISTING | EXISTING | COUPLING |
WASHER | WASHER | CONE | NUT |
| |||
COUPLING | EXISTING | WASHER |
|
|
| ||
COUPLING | COUPLING |
| |
NUT |
| ||
| NUT | NUT |
|
WATER | WATER | WATER | WATER |
These parts must be used as | Use existing | Use existing spiral cone | Captive cone |
illustrated to insure | coupling nut | washer. Fluidmaster cone | washers already |
connection. Use of existing | and washer. | washer may not seal | included. No |
coupling nut may result in |
| completely on spiral type | additional |
water leakage. Water supply |
| supply line. | washers needed. |
tube or pipe must extend at |
|
|
|
least 1/2" inside threaded |
|
|
|
shank of valve (does not |
|
|
|
apply to flanged tubing). |
|
|
|
CAUTION: DO NOT USE |
| CAUTION: Overtightening of |
CONE WASHER WITH |
| LOCK NUT or COUPLING |
| NUT could result in breakage | |
PLASTIC SUPPLY LINE. |
| |
| and potential flooding. | |
|
|
|
8b
With correct washers in place (see Step 8a), tighten COUPLING NUT 1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
9
TOP | ARM NIPPLE |
| |
|
| ||
| REFILL |
| |
| TUBE | TANK | |
|
| LEVER | |
CRITICAL LEVEL |
|
| |
MARK ("C.L.") |
|
| |
MUST BE |
|
| |
1" ABOVE |
|
| |
OVERFLOW PIPE | FLOAT |
| |
|
| ||
| CUP | Fig. 9a | |
|
| ||
FILL |
|
| |
VALVE |
|
| |
VALVE | WATER LEVEL |
| |
ADJUSTMENT |
| ||
BODY |
| ||
ROD |
| ||
|
| ||
ADJUSTABLE |
|
| |
HEIGHT |
|
| |
| SHANK |
| |
| WASHER |
| |
LOCK NUT | THREADED |
| |
CONE WASHER | SHANK |
| |
PARTS FOR WATER |
| ||
|
| ||
COUPLING NUT | CONNECTION |
| |
(SEE STEP 8) | Diagram 1 | ||
(HAND TIGHT ONLY) | |||
|
ADJUSTMENTS:
Turn supply on.
a.Adjust water level to level indicated on tank by adjusting float cup. See Step 10.
b.If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead chain from the retainment clip (see Fig. 9a) and take up slack on the chain, and reinsert on lift rod. Make sure the chain is not too taut.
10
Turn on water supply. Submerge the FLOAT CUP under the water for 30 seconds. Adjust the water to desired level by turning WATER LEVEL ADJUSTMENT ROD and moving FLOAT CUP up or down.
- 2 - |
