|
| Installation | |
TOWN SQUARE | Instructions | ||
| 2555.400 | ||
BIDET FITTINGwith EverClean™ Finish | |||
|
Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets.
EverClean Finish
•One wipe effortlessly removes spots•Eliminates the need for cleaners and scrubbing•Permanent surface protectant remains beautiful for the life of the faucet
•EverClean™ available on: Polished Chrome, Satin Nickel,Stainless Steel, Polished Brass (or any combination of these finishes)Certified to comply with ASME A112.18.1M U.S. Patent No. 5,819,789
. 3 & 7
To ensure that your installation proceeds
Required Tools |
|
| |
Flat Blade Screwdriver | 5VCJOH$VUUFS | ||
|
|
| |
| Phillips Screwdriver |
|
|
| *Hex key |
| Adjustable Wrench |
| *Wrench |
| |
*Supplied with Fitting |
| Channel Locks | |
|
|
| |
BIDET FAUCET INSTALLATION | |||
CAUTION | Turn off hot and cold water | ||
supplies before beginning. |
|
|
| FINISHED |
| TRANSFER VALVE | WALL | |
| (FOR FLUSHING |
| |
| RIM OR SPRAY) |
| |
BIDET OUTLINE |
|
| |
IS SYMBOLIC | 7/8 DIA. |
| |
DOUCHE ADJ. |
| ||
SPRAY | TO | DIA. |
|
|
| ||
DIA. |
|
| |
|
| ||
|
|
|
Assemble MOUNTING NUTS with RUBBER WASHERS (1) onto the VALVE BODIES (2) and insert VALVE BODIES (2) through outside holes, from underside of the BIDET LEDGE. Drop the RUBBER RING (3) over the VALVE BODIES (2) and screw on the ESCUTCHEON (4) until it locks against the internal stop.
Tighten the MOUNTING NUT (1) to secure the VALVE BODY (2).
Remove ESCUTCHEON (5), FRICTION RING (10) and UPPER GASKET (7) from TRANSFER VALVE (8) and insert into the center forward hole of BIDET.
8 TO 12
(C)(H)
FINISHED
FLOOR
DIVERTER
ASSEMBLY
FOR GROUND JOINT CONNECTION OR 1/2 " O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
Replace UPPER GASKET (7) and FRICTION RING (10). Position the side threaded outlet rearward and secure by tightening MOUNTING NUT (9). Thread ESCUTCHEON (5) onto TRANSFER VALVE (8) until it seats against the
STOPPER
BIDET LEDGE.
5
4
3
BIDET
LEDGE
10
2
Thread LOCKNUT (6), WASHER (7) and GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET | 8 | |
and thread FLANGE (9) fully onto | ||
BODY (5). | 7 | |
Tighten LOCKNUT (6) firmly, keeping the | ||
| ||
PIVOT ROD (3) pointed towards the back |
| |
of the BIDET. | 6 |
Place STOPPER into drain and assemble
9
PUTTY
BIDET
CLIP
4 2
3 1
HOT |
| COLD |
1 | 8 | 7 |
|
| |
|
| 9 |
Push DRAIN ESCUTCHEON (10) onto TAILPIECE (11).
5
11
10