American Standard 2555.801 installation instructions Install Handles

Models: 2555.801

1 6
Download 6 pages 39.29 Kb
Page 4
Image 4
10 INSTALL HANDLES

10 INSTALL HANDLES

Turn VALVE to OFF position.

Figure A: Install STEM ADAPTERS (7) onto VALVE STEMS (8).

Figure B: With colored side up, place FRICTION RING (6) over DECK ADAPTER (10). Loosely screw FRICTION NUT (5) onto DECK ADAPTER (10). Do not tighten. Align flats on FRICTION NUT (5) with RIBS (9) in HANDLE BASE (4). Figure C: Screw HANDLE BASE (4) with FRICTION NUT (5) onto DECK ADAPTER (10) until snug against mounting surface and aligned properly.

Figure D: Install LEVER HANDLE (3) onto HANDLE ADAPTER (7) and align. Check alignment, if not satisfactory remove and align. Insert HANDLE SCREW (2) and tighten. Press in INDEX BUTTON (1).

 

 

4

9

 

 

 

 

 

 

 

4

2

1

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

 

 

 

6

 

5

 

3

 

 

FLATS

 

 

 

 

 

 

7

 

10

 

 

 

 

8

6

 

 

4

 

 

 

 

 

 

 

10

10

ALIGNED

 

 

 

 

 

 

 

Figure A

Figure B

Figure C

Figure D

 

 

 

11

TEST INSTALLED FITTING

 

 

5

1

 

 

 

 

With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks.Manual background

Remove AERATOR (3).Operate both HANDLES (1) to flush water

1

lines thoroughly.

Replace AERATOR (3).

12 CHECK DRAIN CONNECTIONS

Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. If STOPPER

(4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.

Release POP-UP KNOB (5) down and check all drain connections and

 

"P" trap for leaks. Tighten if necessary.

HOT

WASTE OUTLETManual background

3

4

2

COLD

Manual background“P” TRAP

 

 

 

 

2

13

CARE INSTRUCTIONS:

14 SERVICE

 

1

 

 

To change direction of handle rotation,

 

DO: SIMPLY RINSE THE PRODUCT

 

 

proceed as follows:

 

 

CLEAN WITH CLEAR WATER.DRY

 

 

Turn valve to OFF position. See step 11 and

 

WITH A SOFT COTTON FLANNEL

 

reverse to remove HANDLE ASSEMBLY (1).

 

CLOTH.

90°

 

 

 

 

Remove SPRING CLIP (2). Lift STOP

 

3

DO NOT: DO NOT CLEAN THE

 

 

WASHER (3), turn 90° and replace.

2

 

PRODUCT WITH SOAPS, ACID,

Replace SPRING CLIP (2).

 

 

 

POLISH, ABRASIVES, HARSH

See step 11 for replacing HANDLE

 

 

CLEANERS, OR A CLOTH WITH

 

 

ASSEMBLY (1).

 

 

A COARSE SURFACE.

 

 

 

 

 

 

 

 

 

M968787 Rev. 1 . 3

4

Page 4
Image 4
American Standard 2555.801 installation instructions Install Handles