5 HANDSHOWER INSTALLATION (Model 2555.901 series only)
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2) is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) BRASS WASHER (4) and LOCKNUT from underside of ledge.
9
11
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT.
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple at the bottom of COUPLING (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY ESCUTCHEON (1). Install SEAL (9) and connect both HOSES (8) and (10), Connect HAND SHOWER (11) to SPRAY HOSE (8).
NOTE When not in use, HANDSHOWER should be seated in the HOLDER.
7
6
5
10
1
2
3
4
LOCKNUT
8
9
6 TEST INSTALLED FAUCET |
| CAUTION | ||
|
|
|
| The flow rate of this Tub Filler exceeds 20 gallons/minute |
| Turn VALVES "off" and attach handles. |
| at higher water pressure. Do not fill bathtub unattended. | |
| With handles in "off" position, turn on water supplies and check | Lift HANDSHOWER from HOLDER, direct spray into tub, lift | ||
| all connections for leaks. |
| ||
|
| TRANSFER KNOB to check HANDSHOWER and HOSES for leaks. | ||
| Operate both handles and flush water lines thoroughly. | |||
| Turn handles "off." | |||
| Check SPOUT mounting for leaks. |
| ||
|
|
| ||
7 | Before the bathroom is completely finished, you may |
| ||
want to remove spout, handshower, and handles. |
| To remove handles, reverse steps in section 4. | ||
|
|
|
| To remove SPOUT (1), proceed as follows: |
| 3 | 5 | 7 | Lift TRANSFER ROD (2) and unscrew KNOB (3). (Model 2555.901only). |
|
| Remove PLUG BUTTON (4) and remove SET SCREW (5) using 5mm hex | ||
|
| 2 |
| |
|
|
| wrench supplied. | |
|
| 4 |
| Lift SPOUT (1) off SHANK (6) carefully and remove RUBBER RING (7). |
|
| 8 |
| Unscrew SHANK SLEEVE (8) and lift TRANSFER ROD (2) from |
| 1 |
| 6 | SHANK (6). (Model 2555.901only). |
|
| Reverse sequence to | ||
|
|
|
| RING (7) is properly seated in its recess at the base of the SPOUT (1). |
Make certain SET SCREW (5) is properly aligned and tight so that
Hex wench, supplied | SPOUT (1) is locked in place. |
|
8 SERVICE
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP (1) and remove
HANDLE SCREW (2).
Pull off HANDLE (3) and unscrew
ESCUTCHEON BASE (4).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90° and replace.
Replace SPRING CLIP (6).
Reinstall ESCUTCHEON (4) and HANDLE
ASSEMBLY.
If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.
HOT LINE FOR HELP
For
1 (800)
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO
Product names listed herein are trademarks of American Standard Inc. © American Standard Inc. 2002
1
2
3
4
90$
5
6
9
EverClean™ Finish Care
Instructions
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
. 3 F W