American Standard 2484.516 Repair Parts List, 12FLUSH BUTTONS ON TANK, Care And Cleaning

10
		PUSH
		BUTTON
TOP	ARM	NIPPLE
CRITICAL
LEVEL MARK
("C.L.") MUST
BE 1" ABOVE		SET WATER
OVERFLOW			FLUSH
		LEVEL HERE
PIPE			VALVE
	FLOAT
	CUP
FILL			PARTIAL
			FLUSH
VALVE
			ADJUSTMENT
			FULL
VALVE	WATER LEVEL		FLUSH
BODY			ADJUSTMENT
	ADJUSTMENT		BAYONET
		ROD
ADJUSTABLE			RELEASE
HEIGHT			SILICONE
		SHANK	SEAL
			VALVE
		WASHER	SEAT
LOCK NUT		THREADED

ADJUSTMENTS

a.Adjust water level. Water level should be adjusted to level indicated on tank by adjusting float cup.

See Step 11 for water level

adjustment method.

b.Make sure Full Flush Adjustment is at the bottom setting (0). A higher setting will result in less water and is not recommended.

c.Make sure Partial Flush Adjustment is at the bottom setting (0). A higher setting will result in less water and is not recommended.

NOTE: The Fill Valve does not have a refill tube. The refill port on the Fluidmaster fill valve is 100% blocked off. Please ensure that the correct repair part is used as this fill valve varies from the standard Fluidmaster 400A.

11

Turn on water supply. Submerge the FLOAT CUP under the water for 30 seconds. Adjust the water to desired level by turning

WATER LEVEL ADJUSTMENT ROD and moving FLOAT CUP up or down.

CONE WASHER	SHANK
	PARTS FOR WATER
COUPLING NUT	CONNECTION
	(SEE STEP 9)
(HAND TIGHT ONLY)
	Diagram 1

•To remove Flush Valve, apply slight downward pressure and twist it until the flush valve disengages from the bayonet.

•To reinstall Flush Valve, reverse the above procedure making sure the blue (Partial Flush Button) will line up with the Partial Flush Button on the Tank Lid.

12FLUSH BUTTONS ON TANK

•Pressing both buttons at once will flush the full flush amount

1.6gal/flush or 6L/flush.

•The Partial Flush Button should line up over the blue actuator on the flush tower in the tank.

•The Full Flush Button should line up over the white actuator on the flush tower in the tank.

Small button for

liquid waste.

.8 gal/flush

3L/flush

Large button for

solid waste.

1.6gal/flush

6L/flush

13

!

CARE AND CLEANING

When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish.

WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage.

American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite).

REPAIR PARTS LIST

Repair parts are determined by toilet tank number which can be found marked inside tank.
NOTE: "XXX" represents color or trim finish options. Specify when ordering.		TANK NUMBER
PART NO.	DESCRIPTION	4035.216	4035.516
735130-400-XXX0A	TANK COVER WITH PUSH BUTTON	✔	✔
738565.426-0070A	FLUIDMASTER 400A VALVE	✔
738565.427-0070A	FLUIDMASTER 400A VALVE		✔
7301143-0070A	TANK COUPLING KIT #258	✔	✔
7381002-400.0070A	DUAL FLUSH VALVE	✔
7381002-401.0070A	DUAL FLUSH VALVE		✔
7381003-XXX0A	PUSH BUTTON ASSEMBLY - TOP MOUNT	✔	✔
034783-XXX0A	BOLT CAP KIT	✔	✔
760127-XXX0A	TOILET SEAT	✔	✔
760130-XXX0A	TOILET SEAT - SLOW CLOSE	✔	✔
7381042-0070A	FLUSH VALVE SILICONE SEAL	✔	✔

- 3 -

7301144-100 Rev. F