6
BOLT CAP
CLOSET FLANGE |
7Tank Installation Kit Includes:
2 bolts, 2 rubber washers, 4 metal washers, 4 metal nuts, 2 plastic nuts, 1 large rubber gasket.
RUBBER
WASHER
RUBBER
TANK MTG. 
GASKET
BOLTS
WASHER
NUT
WASHER
NUT
CLOSET BOLT
WASHER NUT
INSTALL TOILET
a.Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.
!CAUTION:
DO NOT OVERTIGHTEN NUTS
b.Install caps on washers.
c.Smooth off the bead of sealant around base. Remove excess sealant.
INSTALL TANK
a.Discard plastic nuts.
b.Install tank mounting bolts and rubber washers from inside tank, through mounting holes and secure with one metal washer and one nut per bolt.
c.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening.
d.With tank parallel to wall, secure tank to bowl using remaining two metal washers and nuts. Alternately tighten nuts until tank is snugged down evenly against bowl surface.
*USE NUT DRIVER OR DEEP SOCKET RACHET.
!CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
8 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
9a | Before continuing, determine the type of water supply connection you have from |
| the chart below and use the appropriate assembly parts required to properly |
| reconnect the water supply. DO NOT use plumber's putty to seal these fittings. |
METAL / COPPER | METAL FLANGED | METAL SPIRAL | VINYL / BRAIDED | |||
FLARED TUBING |
| TUBING | TUBING | CONNECTOR | ||
LOCK NUT |
| LOCK NUT |
| LOCK NUT | LOCK NUT | |
CONE |
| EXISTING |
| EXISTING | COUPLING | |
| WASHER |
| ||||
WASHER |
|
| CONE | NUT | ||
COUPLING |
| EXISTING |
| WASHER |
| |
|
|
|
| |||
NUT |
| COUPLING |
| COUPLING |
| |
|
| NUT |
| NUT |
| |
WATER |
| WATER |
| WATER | WATER | |
|
| |||||
These parts must be used as |
| Use existing | Use existing spiral | Captive cone | ||
illustrated to insure | coupling nut | cone washer. | washers already | |||
connection. Use of existing |
| and washer. | Fluidmaster cone | included. No | ||
coupling nut may result in |
|
|
| washer may not | additional washers | |
water leakage. Water supply |
|
|
| seal completely on | needed. | |
tube or pipe must extend at |
|
|
| spiral type supply |
| |
least 1/2" inside threaded |
|
|
| line. |
| |
shank of valve (does not |
|
|
|
|
|
|
apply to flanged tubing). |
|
|
|
|
|
|
|
|
|
| |||
CAUTION: DO NOT USE |
|
| CAUTION: Overtightening of | |||
CONE WASHER WITH |
|
| LOCK NUT or COUPLING NUT | |||
|
| could result in breakage and | ||||
PLASTIC SUPPLY LINE. |
|
| potential flooding. | |||
9b
With correct washers in place (see Step 9a), tighten COUPLING NUT 1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
- 2 -
