American Standard installation instructions 2806E SERIES WHIRLPOOL, Installation Instructions

WILLIAMSBURG ELITE™ 6'

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2806E SERIES WHIRLPOOL

INSTALLATION INSTRUCTIONS

1829mm

279mm		(72)
(11)
	ON/OFF
	SWITCH
457mm	229 x 330mm	PUMP
(18)	(9 X 13)
	FLOOR
	CUTOUT

914mm

(36)

INTEGRAL

FITTING DECK

140mm		OUTLINE OF	PROVIDE ACCESS
(5-1/2)	C/L OF
		CUTOUT	TO PUMP FOR SERVICE
	DRAIN
			ON ALL INSTALLATIONS
	OVERFLOW
C/L OF	108mm	LEVELING STRINGER
OVERFLOW	(4-1/4)	(NOT FOR SUPPORT)
				IN-LINE HEATER
				REMOVABLE
	51mm			BLANK
				546mm
INTEGRAL	(2)			(21-1/2)
FEET			495mm
SUPPORT
			(19-1/2)
ROUGH
FLOOR
	1-1/2 N.P.T.M. THREADS
	1-1/2 O.D.TAILPIECE		51mm	108mm
				(4-1/4)
			(2)
	GENERAL SPECIFICATIONS FOR 2806E WHIRLPOOL
INSTALLED SIZE		72 x 36 x 21-1/2 In. (1829 x 914 x 546mm)
WEIGHT			135 Lbs. (61 Kg.)
WEIGHT w/WATER			744 Lbs. (338	Kg.)
GAL. TO OVERFLOW			73 Gal. (276 L)
WHIRLPOOL MIN. OPERATING VOL.			44 Gal. (167 L)
BATHING WELL AT SUMP		45 x 24 In. (1143 x 610mm)
BATHING WELL AT RIM		60 x 30 In. (1524 x 762 mm)
WATER DEPTH TO OVERFLOW			14-1/2 In. (368mm)
FLOOR LOADING		41 Lbs./Sq.Ft. (198 Kgs./Sq.m)
(PROJECTED AREA)
PTS.				25.6
CUBE (FT3)				49.4
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP		2.1 HP, 14.4 AMPS ,120V.

GENERAL INSTALLATION INFORMATION

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

•Flex-Jet Pulse Jet Kit*

•Flex-Jet Soft Jet Kit*

•E-Z-Install Heater*

List of Required Components (not included):

• Drain* • Bath Filler*

* see your Home Depot Retailer

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	20 amp GFI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2003

752872-100 REV. CAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.