6
BOLT CAP
CLOSET FLANGE
CLOSET BOLT
WASHER NUT
INSTALL TOILET
a.Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.
!CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b.Install caps on washers. (If necessary, cut bolt height to size before installing caps.)
c.Smooth off the bead of sealant around base. Remove excess sealant.
7
RUBBER
WASHER
RUBBER
TANK MTG. 
GASKET BOLTS
WASHER
NUT
INSTALL TANK
a.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening.
b.Insert tank mounting bolts and rubber washers from inside tank, through mounting holes, and secure with metal washers and nuts.
c.With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
!CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
8 INSTALLING TANK COVER (with wood trim) 9860.000
COVER
WOOD
TRIM
BLACK
VAPOR
BARRIER
INSTALLATION
Place wood trim with hook and loop strips on tank rim, vapor barrier side down. Hand press in place. Insert pull handle rod into escutcheon on tank cover. Place tank cover on to wood trim. Tip wood trim with cover rear ward to allow hand access into tank and install hook on flapper bead chain to end hole (lower) in pull handle. Place lid in place.
9
INSTALLING TANK COVER (without wood trim)
Insert pull handle rod into escutcheon on tank cover.
Place tank cover on tank, tip cover rear ward to allow for hand access into tank and install hook
on flapper bead chain into second hole (upper) in pull handle rod.
Place lid in place.
10 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
11a | Before continuing, determine the type of water supply connecation you | |||||
| have from the chart below and use the appropriate assembly parts | |||||
| required to properly reconnect the water supply. DO NOT use plumber's | |||||
| putty to seal these fittings. |
|
| |||
| METAL/COPPER | METAL FLANGED | METAL SPIRAL | VINYL/BRAIDED | ||
| FLARED TUBING | TUBING | TUBING | CONNECTOR | ||
| LOCK NUT | LOCK NUT | LOCK NUT | LOCK NUT | ||
| CONE | EXISTING | EXISTING | COUPLING | ||
| WASHER | WASHER | CONE | NUT | ||
|
|
|
| |||
| COUPLING | EXISTING | WASHER |
| ||
|
|
| ||||
| COUPLING | COUPLING |
| |||
| NUT |
| ||||
|
| NUT | NUT |
| ||
| WATER | WATER | WATER | WATER | ||
| ||||||
These parts must be used as | Use existing | Use existing spiral | Captive cone | |||
illustrated to insure | coupling nut | cone washer. | washers already | |||
connection. Use of existing | and washer. | Fluidmaster cone | included. No | |||
coupling nut may result in |
|
|
| washer may not | additional washers | |
water leakage. Water supply |
|
|
| seal completely on | needed. | |
tube or pipe must extend at |
|
|
| spiral type supply |
| |
least 1/2" inside threaded |
|
|
| line. |
| |
shank of valve (does not apply |
|
|
|
|
| |
to flanged tubing). |
|
|
|
|
| |
|
|
|
|
| ||
| CAUTION: DO NOT USE |
|
| CAUTION: Overtightening of | ||
| CONE WASHER WITH |
|
| LOCK NUT or COUPLING NUT | ||
|
|
| could result in breakage and | |||
| PLASTIC SUPPLY LINE. |
|
| potential flooding. | ||
|
|
|
|
|
|
|
- 2 - | 7 3 0 4 9 8 - 1 0 0 |
|
