American Standard 7048.401 Secure joint for water- tight assembly, United States, Mexico Canada

Right Hand Shown

4

Before applying the sealant, place the sink temporarily into the cutout. Check for alignment and clearance, then trace around the outside edge of the

6 Apply a generous portion of silicone sealant inside line traced on countertop. Carefully lower sink into place and press down firmly. Use guidelines for proper positioning. Using water to dampen your finger, remove excess sealant for a smooth even line. Apply additional sealant if necessary to provide a uniform bead from the rim of sink to the masking tape line as shown. Carefully remove tape. Dampen finger and run it slightly over the sealant to remove any high spots.

sink as a guide for installation location and application of sealant. Remove sink.

5	Apply a masking tape outline 1/8" outside traced
	outline as a guide for application of silicone sealant.

Masking Tape

Silicone Sealant

Sink

	Cutout
Masking	1/8"	Sink
tape		outline
outline

7

Connect supply lines to faucet finger tight, and carefully bend to engage with the supply stops. Tighten connections to faucet for secure seal.

Right Hand Shown

AMERICAN STANDARD TEN-YEAR LIMITED WARRANTY

CORIAN® SINK

If inspection of the Corian Sink of this American Standard product, within ten years after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.

This warranty applies only to the original purchaser and installation of these products. All labor and transportation costs or charges incidental to warranty service are to be borne by the original consumer-purchaser.

8

Connect drain assembly hand tight to check alignment. It may be necessary to cut off part of the tailpiece (area "A") or part of the horizontal leg of the trap (area "B").

A

B

This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation.

This warranty shall be void if the product has been fabricated or modified in a manner inconsistent with the product as shipped by American-Standard; moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damages; or if it was not installed in accordance with American Standard's instructions.

Secure joint for water- tight assembly.

Trap

Right Hand Shown

American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)

Corian® Care & Maintenance Tips

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state of from province to province, in which case this warranty does not affect such statutory rights.

In the United States:
American Standard Inc.,	For residents of the United States,
P. O. Box 6820	warranty information may also be
Piscataway, NJ 08855	obtained by calling the following
Attention: Director of Consumer Affairs	toll free number: (800) 223-0068
In Mexico:	In Canada:
Customer Service Manager	American-Standard,
Ideal Standard, S.A. de C.V.	2480 Stanfield Road,
Via Morelos #330	Mississauga, Ontario
Col. Santa Clara	Canada L4Y 1S2
Ecatepec 55540 Edo. Mexico	Toll free: (800) 387-0369
	Toronto Area: (905) 949-4800

Cleaning

Most dirt and stains

Water marks

Difficult stains

Disinfecting

Use soapy water or ammonia-based cleaner.

Wipe with damp cloth; towel dry.

Use an abrasive cleanser and a green Scotch-Brite* pad.

Occasionally wipe surface with diluted household bleach

(1 part water/1 part bleach).

Maintenance Rub with Scotch-Brite* pad alone.

*Registered trademark of the 3M Company

7 9 0 7 6 0 - 1 0 0 2