2
Mount the faucet and drain assembly on the sink following the manufacturer's instructions.
5 Apply a generous portion of silicone sealant inside line traced on countertop. Carefully lower sink into place and press down firmly. Use guidelines for proper positioning. Using water to dampen your finger, remove excess sealant for a smooth even line. Apply additional sealant if necessary to provide a uniform bead from the rim of sink to the masking tape line as shown. Carefully remove tape. Dampen finger and run it slightly over the sealant to remove any high spots.
3 Before applying the
sealant, place the sink temporarily into the cutout. Check for
alignment and clear- ance, then trace
around the outside edge of the sink as
a guide for installation location and application of sealant. Remove sink.
Masking
Tape
6
Connect supply lines to faucet finger tight, and carefully bend to engage with the supply stops.
Silicone Sealant
Sink
4 Apply a masking tape outline 1/8" outside traced out- line as a guide for application of silicone sealant.
Cutout | Sink |
outline | |
1/8" |
|
Masking |
|
tape |
|
outline |
|
Tighten connections to faucet for secure seal.
7
Connect drain assembly hand tight to check alignment. It may be
AMERICAN STANDARD TEN-YEAR LIMITED WARRANTY
CORIAN® SINK
If inspection of the Corian Sink of this American Standard product, within ten years after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.
This warranty applies only to the original purchaser and installation of these products. All labor and transportation costs or charges incidental to warranty service are to be borne by the original
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local
necessary to cut off part of the tailpiece (area "A") or part of the horizontal leg of the trap (area "B").
Secure joint for water- tight assembly.
A
B
building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been fabricated or modified in a manner inconsistent with the product as shipped by
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
Trap
Double Bowl
Corian® Care &
Maintenance Tips
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state of from province to province, in which case this warranty does not affect such statutory rights.
In the United States: |
|
|
American Standard Inc., | For residents of the United States, | |
P. O. Box 6820 | warranty information may also be | |
Piscataway, NJ 08855 | obtained by calling the following | |
Attention: Director of Consumer Affairs | toll free number: (800) | |
In Mexico: | In Canada: | |
Customer Service Manager | ||
Ideal Standard, S.A. de C.V. | 1401 Dupont Street, | |
Via Morelos #330 | Toronto, Ontario | |
|
| Canada M6H 2B1 |
Cleaning
Most dirt and stains
Water marks
Difficult stains
Disinfecting
Use soapy water or
Wipe with damp cloth; towel dry.
Use an abrasive cleanser and a green
Occasionally wipe surface with diluted household bleach
(1 part water/1 part bleach).
Col. Santa Clara |
|
Ecatepec 55540 Edo. Mexico | Toll free: (800) |
Maintenance Rub with
*Registered trademark of the 3M Company
7 9 0 7 5 9 - 1 0 0 R E V A | 4 |
